|
| TROUBLESHOOTING |
| |||||
|
|
| Observe all Safety Guidelines detailed throughout this manual |
| ||||
|
| PROBLEMS |
| POSSIBLE | RECOMMENDED |
| ||
|
| (SYMPTOMS) |
| CAUSE | COURSE OF ACTION |
| ||
|
|
|
|
| OUTPUT PROBLEMS |
|
| |
|
| Major Physical or Electrical | 1. | Contact your Local Lincoln |
|
| ||
|
| Damage is Evident |
|
| Authorized Field Service Facility. |
|
| |
|
| There is no wire feed or open cir- | 1 | The gun trigger or cable may be |
|
|
| |
|
| cuit voltage when the gun trigger is |
| faulty. Check or replace gun |
|
| ||
|
| pulled. Input power is applied to | 2. | assembly. |
|
| ||
|
| POWER MIG 215. |
| The thermal protection circuit |
|
| ||
|
|
|
|
| may be activated. If this is the |
|
| |
|
|
|
|
| case allowing the machine to |
|
| |
|
|
|
| 3. | cool will clear the error condition. |
|
| |
|
|
|
| Make sure input voltage is cor- |
|
| ||
|
|
|
|
| rect and matches nameplate rat- |
|
| |
|
|
|
|
| ing and reconnect panel configu- |
|
| |
|
|
|
| 4. | ration. |
|
| |
|
|
|
| If spool gun option kit is in |
|
| ||
|
|
|
|
| stalled, check to see that it is set |
|
| |
|
|
|
|
| to “Normal” if pulling the gun trig- |
|
| |
|
|
|
|
| ger associated with built in feed- |
|
| |
|
|
|
|
| er, and “Spool Gun” if pulling | If all recommended possible areas | ||
|
|
|
|
| spool gun trigger. | |||
|
|
|
|
|
|
| of misadjustment have been |
|
|
| Output voltage and wire feed is pre- | 1. | Remove gun assembly from |
| |||
|
| checked and the problem persists, | ||||||
|
| sent when gun trigger is not pulled |
| machine. If problem is solved | Contact your local Lincoln |
| ||
|
| (not activated). |
|
| gun assembly is faulty. Repair or | Authorized Field Service Facility. | ||
|
|
|
| 2. | replace. |
|
| |
|
|
|
| If problem persists when gun |
|
| ||
|
|
|
|
| assembly is removed from |
|
| |
|
|
|
|
| machine then the problem is |
|
| |
|
|
|
|
| within the POWER MIG 215. |
|
| |
|
| Machine output is low. Welds are | 1. | Check input voltage. Make sure |
|
|
| |
|
| “cold”, weld bead is rounded or |
| input voltage matches name- |
|
| ||
|
| bumped up demonstrating poor |
| plate rating and reconnect panel |
|
| ||
|
| wetting into plate. |
| 2. | configuration. |
|
| |
|
|
|
| Make sure settings for wire feed |
|
| ||
|
|
|
|
| speed and voltage are correct |
|
| |
|
|
|
| 3. | for process being used. |
|
| |
|
|
|
| Make sure output polarity is cor- |
|
| ||
|
|
|
| 4. | rect for process being used. |
|
| |
|
|
|
| Check welding cables and gun |
|
| ||
|
|
|
|
| assembly for loose or faulty con- |
|
| |
|
|
|
|
| nections. |
|
| |
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed.
POWER MIG 215
