Front Panel | Linksys PAP2-VU guide

Phone Adapter with 2 Ports for Voice-over-IP

The Front Panel

The Phone Adapter’s LEDs are located on the front panel.

	Figure 2-2: Front Panel
PHONE 1 LED	Blue. The PHONE 1 LED is solidly lit when a telephone or fax machine has a registered
	connection to your Internet phone service provider through the PHONE 1 port. (The
	connection is registered if your Internet phone service account is active.) It flashes when
	the phone is being used or an incoming call has been detected.
PHONE 2 LED	Blue. The PHONE 2 LED is solidly lit when a telephone or fax machine has a registered
	connection to your Internet phone service provider through the PHONE 2 port. It flashes
	when the phone is being used or an incoming call has been detected.
ETHERNET LED	Blue. The ETHERNET LED lights up when the Phone Adapter is connected to your network
	through the Ethernet port. It flashes when there is data being sent or received.
Power LED	Blue/Red. The Power LED lights up when the Phone Adapter is powered on and ready. It
	flashes when the Phone Adapter is booting up, undergoing a self-test, or performing a
	firmware upgrade. The LED lights up red when the Phone Adapter has failed its self-test or
	is malfunctioning. Refer to “Appendix A: Troubleshooting” for more information.
4	Chapter 2: Getting to Know the Phone Adapter
	The Front Panel

Image 9

Linksys PAP2-VU manual Front Panel, Phone Adapter’s LEDs are located on the front panel

Contents

Division of Cisco Systems, Inc Phone AdapterPage Copyright and Trademarks How to Use this Guide Table of Contents Front Panel Back Panel Introduction WelcomeWhat’s in this Guide? What’s in this Guide? Back Panel Ports Getting to Know the Phone Adapter Front Panel Phone Adapter’s LEDs are located on the front panelPhone is being used or an incoming call has been detected Instructions for Connecting the Phone Adapter Connecting the Phone AdapterOverview Internet Connect the Telephone Cable Stand Option Placement OptionsRemove the plate from the Phone Adapter’s bottom panel Phone Adapter’s Interactive Voice Response Menu Measurement between Wall-Mount Slots Wall-Mount Option Using the Phone Adapter’s Interactive Voice Response Menu Accessing the Interactive Voice Response MenuUsing the Interactive Voice Response Menu Interactive Voice Response Menu Use this command to enter Response MenuNot press any other keys until you Key or hang up to exit 101 Enter 1 to enable Has been enabled or disabled. IfEnter 0 to disable Check Dhcp 100 Static IP address When entering a Decimal point Address usingSubnet Mask Mask using Network mask When entering a Decimal point Static gateway IP address When entering a Decimal point Address Address usingPhone Adapter Manual Reboot 732668 131 Enter the IP Configuring the Settings for Your Internet Phone Service Common Problems and Solutions Appendix a Troubleshooting Appendix a Troubleshooting Internet phone 5060 to Application Start and End Protocol IP Address EnableIP address Phone Adapter Internet phone 53 to IP address Phone Adapter Internet phone 69 to Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Pick up the phone and dial as you normally would Frequently Asked Questions Can I make calls while I’m browsing the Internet? Appendix B Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Dimensions Storage HumidityMm x 101 mm x 15 mm Limited Warranty Appendix E Warranty Information Appendix E Warranty Information FCC Statement Appendix F Regulatory Information Appendix F Regulatory Information Appendix G Contact Information Appendix G Contact Information