Manuals / Linn / Home Audio / Stereo Amplifier

Linn Kolektor owner manual Changing the bass and treble, 9~, ~9, To change the bass or treble

Models: Kolektor

1 48

Download 48 pages 34.4 Kb

Page 27

9~-_

While you are adjusting the balance the display will show the current balance setting, and the BALANCE indicator will be lit:

BALANCE

9~-_

BALANCE

==

BALANCE

_-~9

FULLY LEFT

CENTRE POSITION

FULLY RIGHT

While you are adjusting the balance press + to restore the balance towards the centre position.

Changing the bass and treble

?or &

BASS

0

<>

BASS

5

The KOLEKTOR has individual bass and treble controls to allow you to adjust the sound to suit a wide range of speakers, sources, and room acoustics.

17

To change the bass or treble

Press * or ! (front panel) to display the current bass or treble setting respectively. Then use ( and ) (front panel) to set the bass or treble as required.

Alternatively press BASS- or BASS+ (handset) to set the bass or TREB- or TREB+ (handset) to set the treble.

You can change the bass and treble from -7 (maximum cut), through 0 (level), to +7 (maximum lift).

After adjusting the bass or treble the display will revert to normal after a delay. While you are adjusting bass or treble, pressing * or

!will restore the value towards zero.

Image 27

Linn Kolektor owner manual Changing the bass and treble, 9~, ~9, To change the bass or treble

Contents

P R E A M P L I F I E R O W N E R S M A N U A L LINN KOLEKTORPage MAINS PLUGS Important safety informationGENERAL SAFETY INSTRUCTIONS Replacing the fuse Mains plug replacementDate of issue CE Declaration of ConformityFCC notice Date of issueUnpacking ContentsMaintenance IntroductionSpecifications Technical informationIndex Copyright and acknowledgements viii you will hear the sources in IntroductionL i n n K O L E K T O R With the Linn KOLEKTORAudio module Your Linn KOLEKTORControl module Bass and treble controls Special features of the KOLEKTORIndependent source settings Interface moduleIntelligent operation with other Linn products Configurable source namesRecording lock User optionsSetting up the KOLEKTOR UnpackingPositioning the KOLEKTOR Replacing the fusesLocating the KOLEKTOR for use with the handset Connecting the sources Connecting the KOLEKTORConnecting headphones Connecting a phono sourceConnecting a tape recorder Connecting to a power amplifiersuitable power outlet Connecting the mains supplyUsing the front panel Using the KOLEKTORtu 2 LOCK LINN Using the handsetSwitching on and off To switch onSelecting a source Changing the volume To select a sourceTo select a source directly from the handset To mute the sound To change the volumeChanging the balance ~4To change the bass or treble Changing the bass and treble9~ ~9To set up a recording To cancel a recordingRecording a source Removing inputs Configuring the inputsUsing a moving magnet phono source Customising the KOLEKTORTo select the input to rename To start configuring inputsTo save the new input names Changing user options To change the user optionsTo choose a specific user option To save the user options initial value is shown underlined User optionsRC5 Amplifier Factory default settings To reset the KOLEKTORinit There is no sound from the speakers Troubleshooting and maintenanceTroubleshooting Poor response to handset commandsTechnical support Maintenancecommands CleaningAmerica Audio SpecificationsTechnical information GeneralLinn Interconnect cables LOCK indicator factory default settings 26 front panelfuse replacement handset headphones, connectingpower amplifier, connecting connectingmaintenance MUTE indicatorVOL- and VOL+ keys 12, voltage selection volume, changingunpacking user options user options continuedPage Page Page Page PACK LI N N