Magnavox MDR513H / F7 owner manual Troubleshooting

TROUBLESHOOTING

	Symptom					Remedy
	Certain functions of the DVC cannot					• Some functions may not operate depending on the type of DVC. For
	operate.					example, if the DVC does not support slow playback mode, the slow
						playback function is disabled.
						• With L3(DV-IN), the disc display menu does not appear unless disc
						playback is executed.
	DV audio signal cannot be switched.					• For recording with the DVC, the recording audio signal can be set to 12
GENERAL						bits or 16 bits. However, when 16-bit recording mode is selected, audio
						signal cannot be switched. To record an audio signal, set it to 12 bits.
	No image from HDMI connection.					• Check the HDMI connection. (Check the status of the HDMI related
						indications.)
						• Check whether the connected monitor device or other device supports
						HDCP. (This unit will not output a video signal unless the other device
						supports HDCP.)
						• Check the setting of HDMI.
						• Check whether the output format of this unit (HDMI FORMAT) matches
						the supported input format of other connected device.
	Setup menu cannot be called up.					• Setup menus cannot be called up during DVD recording.
	TV channels cannot be changed.					• Check if the connections are made securely and correctly.
CHANNEL						• Check if the cables are damaged.
						• Try channel setting by following the steps on pages 29-31.
	Only specific channels do not appear.					• The channels may be set to be skipped. (Refer to pages 30-31.)
	The external input channels (such as					• This unit does not skip the external input channels. This is not a
	L1, L2 or L3) cannot be skipped.					malfunction.
		The image from the external device				• Try pressing [SOURCE] repeatedly.
	GENERAL
		cannot be displayed or recorded.				• Turn on all connected devices.
						• Check if the connections are made securely and correctly.
		Recording is impossible.				• It is prohibited to make a recording from 2 minutes before the
						programmed start time of a timer recording.
						• This unit cannot record programs that contain copy protection signal.
	DVD					This is not a malfunction.
						• The space of the recording media may be used up. Try deleting
						unnecessary titles, or exchange it with the recordable media.
	/					• The maximum number of titles or chapters has exceeded. Delete the
	HDD
						unnecessary titles to make enough space or insert a new recordable media.
						• Check if the connections are made securely and correctly.
		Timer recording cannot be				• The internal clock of the unit may have been stopped due to a power
RECORDING		performed.				failure that lasted for more than 30 seconds. Reset the clock. (Refer to
						pages 32-34.)
		The picture of the autostart				• The contents of the autostart recording will be cleared in some cases
		recording disappears.				(Changing input channel etc.). Refer to page 46.
	HDD	When playing back the title				• In the autostart recording, when you display the DTV program
		recorded from the autostart				information, the information will be recorded as the part of the picture.
		recording, the DTV program
		information is displayed and it
		cannot be disappeared.
		Recording is impossible.				• Copy-once programs cannot be recorded on DVD. This is not a
						malfunction.
						• Check if the disc is protected or finalized. Undo the protection or the
						finalization.
	DVD					• DVD-RW once formatted on other unit cannot be recorded on this unit
						unless all the contents in the disc are erased.
						• Check if the connections are made securely and correctly.
		The indication				• “			” may remain on screen for the
							Writing to Disc	100%
		“			”		maximum of 20 seconds even		after it reached 100%. This is not a
			Writing to Disc	100%
		does not disappear.				malfunction.

Introduction Connections Basic Setup Recording Playback

Editing Function Setup Others

Español

EN 115