Marantz DV7110 manual Troubleshooting, Information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest MARANTZ service center or your dealer to carry out repair work.

The disc table comes back out automatically, shortly after the disc table is closed.

The disc is dirty or warped.

\Refer to ‘Disc Care’ (page 48).

The disc is not placed properly on the disc table.

\Use the disc table guide to align the disc (page 18).

Region number does not conform with this unit.

\If the region number on the disc does not match the number on the player, the disc cannot be used (page 54).

There is condensation on the operating section of the player.

\Allow time for condensation to evaporate. If player is near an air conditioning unit, you should move the player (page 49).

Playback is not possible.

The disc has been loaded upside down.

\Check that the disc has been loaded with the label side facing up.

mark appears on screen.

The selected function does not operate for that disc.

mark appears on screen.

The operation is prohibited by the player.

Picture playback stops and the operation buttons cannot be used.

Player malfunctions.

\Stop disc playback (press STOP 7), then start playback again.

New settings made in the Setup screen menus while a disc is playing are ineffective.

Some settings can be changed while a disc is playing, but are not effective. This is not a malfunction.

\Make the same setting when the player is stopped.

\Stop disc playback (press STOP 7), then start playback again. When playback is resumed, the new settings should be in effect. Please note that making settings in the Setup screen menus may cancel the resume function.

When making changes in the Setup screen menus, is displayed.

There is a Video CD or CD loaded in the player and the setting that was changed only applies to DVD performance.

\The setting will be effective the next time a DVD is loaded.

ENGLISH

No picture.

The rear panel’s VIDEO OUT SELECT switch setting is not correct.

\Check that the VIDEO OUT SELECT switch is set to the correct position for the monitor connection you are using (page 14).

Connection is incorrect.

\Check that cord connections are correct and that plugs are firmly connected.

Operation (settings) of TV or AV amplifier is not appropriate.

\Be sure that your TV, receiver, or amplifier is set up to view DVD playback.

The [Component Video] menu is set to [progressive] but your TV/monitor is not compatible with progressive scan.

\Reconnect the player to your TV using a composite or S-video cord, then set set the VIDEO OUT SELECT switch on the rear panel to COMPOSITE & S-VIDEO. With your TV connected using either the composite or S-Video terminals, choose the [Interlace] setting in the [Component Video] menu, then set the rear panel switch back to COMPONENT (page 27).

\Reset the player (page 47). [Component Video] will be reset to [Interlace] but you’ll also loose other settings.

\Check that the VIDEO OFF switch is set to the correct position (page 47).

The screen is stretched or aspect does not change.

The multi aspect setting is not appropriate.

\Change the aspect setting in the [TV Screen] setting in the Setup screen Video menu to the screen type most appropriate to the TV or monitor you are using (page 26).

This is not a malfunction.

\The aspect ratio of some progressive-scan compatible TVs cannot be changed.

Picture disturbance during playback or dark.	ADDITIONAL
picture depending on the TV.
This is not a malfunction.
\ This player is compatible with Macro-Vision System
copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
stripes etc., may appear on some sections of the	INFORMATION
When using progressive-scan.
\ If your TV is connected using the COMPONENT
VIDEO OUT jacks, set the [Component Video] menu
to [Interlace] (page 27).
When recorded on a VCR or passed through an AV
selector, there is disturbance in the playback picture.
This is not a malfunction.

\Due to the player’s copy protection circuits, connection of this device through a VCR or an AV selector may prevent recording or cause picture problems.

Remote control operation is not possible.

The rear panel control input jack on the player is being used.

\Point the remote control at the component that the player is connected to (page 14).

The remote control is too far from the player, or the angle with the remote sensor is too wide.

\Be sure to operate the remote from a location within its operating range (page 8).

The batteries are exhausted.

\Replace the exhausted batteries with all new batteries (page 8).

53