3.Press the command buttons in the desired sequence. When you press a command button to be learned into the macro sequence, its name will appear within the LCD window. Every time you press another remote command, the macro step number increases one by one.

4.It is possible during macro programming to adjust the timing of the interval between several macro steps. Using the cursor keys ⁄6, the interval between macro playback steps can be increased or decreased in 1/2 second steps, over the range beginning at 1/2 second up to 10 seconds. For example, when the indicator shows “0.5 SEC”, if you press the direction key, the interval time would change to 10 sec- onds, then with another press of the direction key, it would change to 9.5 seconds, etc. Use the direction key to increase the interval time, and use the direction key to decrease the interval time. Some equipment may not be able to receive infrared commands in one-half second steps. If after programming a macro you find that the sequence was not properly carried out, you may wish to experi- ment with different sequence timings to obtain the correct operation results, by using the adjustment method described above.

Within each macro button, up to 20 steps can be memorized. In the event that you wish to memorize more than 20 steps per macro, then press another MACRO2 button 6 , and follow the above operations. A maximum of 80 steps can be programmed this way. However, you will probably find that 20 steps is more than enough to carry out even the most complex macro instructions to achieve a specific home theater operating result.

Note: To memorize the cursor button F, press and hold the LIGHTING button J before pressing the cursor button.

When programming macro steps, note that the following but- tons would not normally be included in a macro sequence, and are therefore not available for inclusion in a macro:

MODE 1, MACRO 2, CLONE 3, PAGE 8, VOLUME A, MEMOC, CLEAR D and LIGHTING J.

To check to see which MACRO buttons 6 have been programmed with macros, at the beginning of the macro learning sequence the four numeri- cal (1 through 4) indicators at the bottom of the LCD window will show a box around the number for each MACRO button that already has a macro assigned to it (see Figure 11, which shows that only MACRO but- ton number 1 has a macro assigned to it).

Figure 11

LOW

LEARN

NAME

1234

During the programming sequence, just remember that if you wish to activate a specific input selector on your amplifier or receiver, make sure that you press the desired input selection button FIRST. Subsequent func- tion button selections can be incorporated in the macro sequence, but on playback, the RC2000MKII will only send out a function selection infra- red command to the amplifier or receiver based upon the first function command used in the macro sequence.

For example, you may wish to have a macro sequence which activates the laser disc player input on your amplifier or receiver, and then have additional commands in the sequence to instruct your TV set to switch to an external video source to receive the laser disc video signal. During the macro programming, make sure that you press the LD function selector button BEFORE you press any of the other function selector buttons in the sequence. You can then include any of the TV commands by pressing the TV function selector button, later in the sequence. When this macro is next used (played back), the RC2000MKII will send out the command to change the amplifier or receiver’s input selector to laser disc input (since its function selector button was the first one programmed into that macro sequence), and will not subsequently change the amplifier or re- ceiver’s input to TV (but will send out any special TV commands that you included in the macro sequence).

Note: To AMP button is not include the above functions buttons.

Programming a macro under a function selector key:

If you wish, you can also program a macro that can be activated by press- ing one of the function selector 9 keys. The programming steps are similar to the steps outlined for programming a macro number button 6. The following example shows how to program a macro under the LD (laser disc) function selector 9:

(activate the main amplifier’s power on, switch the source to laser disc, switch the amplifier’s surround mode to PRO LOGIC, switch on the tel- evision, switch to the television’s AUX video input, power up the laser disc player, and begin laser disc playback)

1.Press the MACRO 2 operation mode button with the tip of a paper clip.

2.Press the LD function button 9.

3.Press the following buttons:

POWER ON, LD, AMP, direct function D-5 (PRO LOGIC selector) in page 1, TV*, SOURCE ON, direct function D-4 (VIDEO input selector) in page 1, LD*, SOURCE ON, and PLAY.

4.Press the MACRO 2 button with the tip of a paper clip. The RC2000MKII will revert to the normal mode and save the macro under the LD function button.

5.To execute the new macro sequence, press twice and hold the LD function selector button for 3 seconds.

In the event that you wish to revise a programmed macro sequence, search the step number you wish to change by using the cursor button and ⁄6, and then re-enter the new command. If you memorized different com- mands than have already been programmed, then the previous macro se- quence will be erased and re-written over with the new sequence. To add the new command, press the MEMO button at your desired point. To delete the sequence, press the CLEAR button at your desired point.

During macro programming, if a button is not pressed within 1 minutes, the mode will automatically revert to the original mode (USE).

When you have completed the macro programming sequence, press the MACRO 2 operation button with the the tip of a paper clip. The “END” indication appears in the LCD display window. When you release the MACRO button, all indications will revert to the initial status.

There is one more important point to note about programming a macro sequence. During a macro sequence, you may include more than one function selection button to access some transport and/or other commands. Depending on the macro sequence, this might result in the amplifier or receiver’s function selection to be inadvertently changed as well when the macro is played back. The RC2000MKII has a special feature to prevent this from occurring, allowing you to access the special commands available under each RC2000MKII function button during a macro play- back sequence, while at the same time prevent the amplifier or receiver from constantly switching its input source back and forth at the same time.

12

PD4292D-2

12

00.10.4, 3:10 PM

Page 18
Image 18
Marantz PD4292D manual Programming a macro under a function selector key

PD4292D specifications

The Marantz PD4292D is a high-performance DVD player that reflects the brand’s commitment to delivering exceptional audio and visual quality. Designed for home theater enthusiasts, this player offers a comprehensive array of features and advanced technologies, making it a standout in the world of multimedia playback.

One of the primary characteristics of the PD4292D is its support for a wide range of media formats. It is compatible with DVD-Video, DVD-Audio, CD, MP3, JPEG, and various other formats, allowing users to enjoy multimedia content from a single device. This versatility means that whether you want to watch movies, listen to music, or view photo slideshows, the PD4292D has you covered.

The imaging technology in the Marantz PD4292D is truly impressive. It includes advanced video processing capabilities that enhance picture quality, making use of progressive scan output for a clearer and sharper image. The player’s compatibility with high-definition formats ensures that users can experience their favorite films and videos in stunning detail, with vibrant colors and deep contrast ratios that enhance visual immersion.

Audio performance is another major feature of the PD4292D. The player supports high-quality audio formats, including Dolby Digital and DTS, allowing for a rich and dynamic sound experience. Additionally, the inclusion of discrete power amplifiers contributes to the overall audio fidelity, giving users an enjoyable listening experience whether they are playing CDs or DVDs.

Connectivity is also markedly robust in the PD4292D. It features multiple outputs, including HDMI, optical, and coaxial outputs, making it easy to connect to a variety of audio and video systems. The HDMI output provides a seamless digital connection to modern televisions and receivers, ensuring that users can enjoy high-definition audio and video without any quality compromise.

User-friendly operation is another hallmark of the Marantz PD4292D. The interface is designed for ease of use, with intuitive controls that allow quick navigation through menus. Furthermore, the player supports various remote control options, making it convenient for users to manage playback from a distance.

In conclusion, the Marantz PD4292D DVD player encapsulates the brand’s philosophy of superior sound and picture quality, combined with versatility and ease of use. Whether you are an avid movie watcher, music lover, or just looking for an all-in-one media solution, the PD4292D offers an impressive range of features that meet the demands of today’s multimedia consumption. With this player, Marantz continues to set a standard for excellence in home entertainment.