Marantz PD4292D manual Direct Command Functions Listing, Lamp Lighting function on or OFF and Time

LAMP - Lighting function ON or OFF and TIME

Press the D-5 direct function button, and you can then set the time (in seconds) directly using the numeric key pad B buttons. A time figure consisting of only 1 digit can be input by pressing the figure then waiting for 2 seconds or input “0” before entering a desired digit. You can set time in the range from 0 up to 60 seconds (which would use up more battery life than a lower figure, such as 3 or 5 seconds). “2” is set when shipped from the factory. You can set “OFF” to input “0”.

BEEP sound

The beep sounds when press any buttons.

The beep sound level can be set to decrease or increase by pressing the D-6 button. The display indicates “+” indication and the beeps are sounded by pressing the D-6 button. The “+” indication is followed the “+” indi- cation as the beep sound is increaded; + → ++ → +++ → ++++

When the “++++” is indicated and the D-6 button is pressed, the mininum level “+” is set.

“ ” is indicated in LCD window when the beep sound is set.

Note: The beep sound is different between the function buttons and other buttons.

VER

Press the D-7 direct function button to switch between US to REST.

If you need to change this function, we recommend that you make the change before you begin “learning” any new infrared codes for other brands of equipment in your system.

Note: The name of the DIRECT button will be erased by changing the VER(sion).

Battery life:

•Battery life will vary from user to user, if the remote is used constantly or only occasionally, including the amount of backlighting usage. We feel that you can expect the batteries to last about 4 months, based upon 15 remote control operations per day (every day), and 3 lighting operations per day (every day). If the remote is used more often, and if the lighting times are set to longer times than the factory settings, then the battery life may be shortened somewhat.

•As explained earlier in the guide, the RC2000MKII’s sophisticated battery conservation system will advise you long before the battery power is fully exhausted, and will further warn you to replace the bat- teries by simply becoming inoperative at a certain point. The custom- ized memory contents and user-adjusted settings will still be retained in memory. When you install a fresh set of batteries, the memory contents are protected always, because the RC2000MKII use the non- volatile memory. Alkaline (and the newer lithium) types are recom- mended for longest battery life.

As you become more familiar over time with how you are using the RC2000MKII in your A/V system, you may wish to consider reducing the lighting time(s) if possible, as this can help to extend the battery life.

Adjustment of the LCD contrast

• The LCD contrast can be adjusted as follows;

Set SETUP mode to the RC2000MKII by pressing the MEMO and OK button. Press the VOL+ to increase the LCD contraset. Press the VOL - to decrease the LCD contrast. Press the OK button to end this setting and return the original operation.

Direct Command Functions Listing

Within the RC2000MKII LCD window, each of the 8 Direct Function buttons has 4 character label attached for pre-programmed remote com- mands. These commands can be used with various Marantz A/V compo- nents, or other components using the Philips RC-5 remote control lan- guage.

You can easily replace the factory-supplied remote command codes with different codes from other brands of equipment. Most functions that are supplied apply to a wide variety of equipment from many companies. The following list shows the remote code assignments for the direct func- tion buttons, for each of the 10 main function selector buttons, as sup- plied from the factory. You can add or replace function commands, in- cluding re-naming them if you wish, in order to customize the RC2000MKII for your own particular selection of A/V components.

AMP	1 MODE-1	1 AC-3		selects Dolby Digital (AC-3) decoding
		2	RF	selects Dolby Digital RF input
		3	OPT	selects optical digital input
		4	COAX	selects coaxial digital input
		5	P/L	Dolby Pro Logic decoding
		6	6-CH	activates 6 channel setup
		7	2-CH	Stereo (no surround decoding)
		8	NITE	selects NIGHT mode
	2 MODE-2	1 AC-3		selects Dolby Digital (AC-3) decoding
		2	P/L	Dolby Pro Logic decoding
		3	3-ST	Dolby 3-stereo decoding
		4	MOV	Movie surround sound
		5	THX	THX Cinema decoding
		6	MTRX	Matrix surround sound
		7	HALL	Hall surround sound
		8	2-CH	Stereo (no surround decoding)
	3 SETUP	1 TEST		activates test tone
		2	DLAY	increases delay time
		3	R-EQ	activates RE-EQ function
		4	ATT	activates ATT function
		5	CH+	next channel (up)
		6	LVL+	increases channel level volume
		7	LVL-	decreases channel level volume
		8	MLTI	activates multi-room mode
	4 PROCESSOR	1 RF		selects Dolby Digital RF input
		2	OPT	selects optical digital input
		3	COAX	selects coaxial digital input
		4	BYP	bypasses Dolby Digital decoding
		5	VOL+	increases Dolby Digital volume
		6	VOL-	decreases Dolby Digital volume
		7	SLEP	activates amplifier’s sleep timer
		8	6-CH	activates 6 channel setup
TUNER	1 BAND	1 FM		FM band
		2 AM		AM/MW band
		3	LW	long wave band
		4	BAND	selects radio band
		5	MODE	mono/stereo/muting mode selector
		6	TIME	time display
		7	F/P	frequency or preset channel display
		8	SCAN	programmed preset channel scan
	2 REC	1 TP-1		commands for Tape 1 control
				(NO output)
		2	REC	record

15

PD4292D-2 15 00.10.4, 3:10 PM