Marantz PD4292D manual Other Functions, RC-5 Shipped destination, Set-Up

To “clone” (duplicate) the memory contents of one RC2000MKII into another RC2000MKII, please follow these steps:

1.Place the source RC2000MKII (the one with all of the customized commands, names, macros, macro sequences, and the like) with its infrared transmitter window L facing the infrared sensor M of an- other “fresh” RC2000MKII (5 cm, or 2 inches apart).

2.Press the CLONE button 3 of the source RC2000MKII with the tip of a paper clip, and select “CLONE TX” (clone transmit) mode (see Figure 20).

Figure 20

3.Press the CLONE button 3of the learning (receiving) RC2000MKII with the tip of a paper clip or a similar object, and select “CLONE RX” (clone receive mode). Then press the PLAY button E.

Figure 21

4.Press the source RC2000MKII’s transport control PLAY E button to begin the infrared data transmission sequence. If you wish to duplicate only 1 to 8 function’s memory, press function button(s) you wish before pressing the PLAY button. Now the “LEARN” indicator starts to blink. (see Figure 23)

Figure 22	Figure 23
	LEARN

After all bars are lit up on both displays, “TX OK” (transmission OK) will appear in the source RC2000MKII’s LCD window, and “RX OK” (reception OK) will appear in the “cloned” RC2000MKII’s LCD win- dow, confirming the end of the copying process (see Figures 24 and 25).

Figure 24	Figure 25
	LEARN

Please be sure that, during the copying process, neither RC2000MKII is physically disturbed (ideally, they should be placed on a table or other surface, and not hand-held during the copying process). If, for some reason, the copying process was interrupted, the “clone” RC2000MKII’s LCD display window will indicate “RX NG” (reception no good). Sim- ply begin the clone process anew by repeating the above steps.

Note: The cloning is available between the same remote control unit series only therefore the RC2000MKII cannot be cloned by RC2000.

5.It the source RC2000MKII’s memory contents are at or near full capacity, the copying process will take about 3 minutes. After com- pletion of the copying (cloning) process, press the CLONE button 3 on both RC2000MKII’s with the tip of a paper clip, and select the OFF mode.

Then, you’ll have two identically programmed RC2000MKII remotes, one of which can again be used as your system’s primary remote control, and you’ll have the added confidence of knowing that in the event of inadvertent programming (or memory contents being cleared somehow), you can simply retrieve the “backup” RC2000MKII that you’ve safely tucked away, and within minutes restore the program- ming contents of the original RC2000MKII with your customized configuration.

Other Functions

The Marantz RC2000MKII includes the ability to tailor the light- ing features according to your preferences. As supplied from the factory, the RC2000MKII has a lighting features (and light- ing timings):

1.The lighting time is set at the factory for a period of 2 seconds which you can change if you prefer a different lighting time. If you wish to maximize battery life, you can defeat the lighting function entirely. There is also a lighting button J, so that in any light situations, you can activate the backlighting feature. The lighting time in this case is set at the factory for a period of 2 seconds, which you can also change. If you wish to conserve battery power, you can de-activate the lighting function entirely.

RC-5 Shipped destination:

As mentioned earlier in this guide, the RC2000MKII is provided with many commands from the factory with infrared codes conforming to the Philips RC-5 remote control language (used by Marantz, Philips, and some other companies). We have provided two different RC-5 command code sets in the RC2000MKII, according to the local requirements of different markets and the different types of remote control codes used in those markets. One code set is for North American (US) users, while the other code set is for REST users. Your RC2000MKII has been set at the factory for US (United States) codes. It can be easily changed, if you wish.

Set-Up:

To change the lighting time(s), or the destination setting, please follow these steps:

•Select the SETUP mode, by holding the MEMO button C and at the same time press the OK button within the cursor keys ⁄6. (see Figures 26 and 27)

Figure 26				Figure 27
LOW			LEARN	LOW			LEARN
			NAME				NAME
1	2	3	4	1	2	3	4

14

PD4292D-2 14 00.10.4, 3:10 PM