Marantz SR9300 manual Preference, Surround, Effect Level

PREFERENCE

ENGLISH
	3 P RE F ERENCE
	T V - AUT O	:	D I SAB L E
	OSD I N FO	:	ENAB L E
	D I G I TA L OU T	:	SOURCE
	S UBWOOF ER OU T	:	T HX
	MA I N		E X I T

1. Select “PREFERENCE” in MAIN SETUP MENU with Up or Down cursor button, and press the OK button.

2. To select a desired content, press Up or Down cursor button.

TV AUTO: Select the TV AUTO ON/OFF function to enable or disable with Left or Right cursor button.

(refer to page 43)

OSD Info: Select the OSD information function to enable or disable with Left or Right cursor button.

If you select “ENABLE”, SR9300 will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select “DISABLE “.

DIG. OUT: Select the digital source to output the DIGITAL OUT

terminals with Left or Right cursor button.

This is for digital dubbing to a CD-R recorder or MD deck. (See page 44)

The source is switched in the following sequence. SOURCE →DIG.1 →DIG.2 → → →DIG.8 →DIG.9 → AUX →OFF →SOURCE →

SUB-W OUT: “THX” position is required, but If you desire an additional front L/R mixed subwoofer output in the STEREO mode, select “L/R MIX” with Left or Right button.

If you finish the setup in this item, move cursor to “MAIN” with Up or Down cursor buttons and press OK button.

SURROUND

4	S URROUND
S URR . MOD E		: AU T O
C I N EMA R E - EQ			: O F F
L F E L E V E L			: 0 d B
S URR	L / R	E F F EC T	: ∗ ∗ ∗ d B
S URR	BACK	E F F EC T	: ∗ ∗ ∗ d B
C EN T ER E F F EC T			: ∗ ∗ ∗ d B
S UB W E F F EC T			: ∗ ∗ ∗ d B
MA I N			E X I T

1. Select “SURROUND” in MAIN SETUP MENU with Up or Down cursor button, and press the OK button.

2. To select a desired content , press Up or Down cursor button.

SURR-MODE :Select the desired surround mode with Left or Right cursor button.

CINEMA RE-EQ™ :Select to active the Cinema Re-EQ™ with Left or Right cursor button.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments. Activating the Cinema Re-EQ™ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance.

Cinema Re-EQ™ is therefore not necessary for material that was not designed for movie theaters (for example, sports programming, television shows, made for TV movies, etc..).

The Cinema Re-EQ™ feature can be activated only while in Dolby Pro Logic Mode, or while decoding Dolby Digital or DTS encoded material.

LFE LEVEL : Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0dB, -10 dB or OFF with Left or Right cursor button.

The level is ordinarily set to 0 dB except DTS- Music mode. In the DTS-Music mode, default level is set to -10 dB.

EFFECT LEVEL

SURR L/R EFFECT: Set the effect level of the Surround speaker between –3 and +3 level in 1 level interval .

•If “None” was selected for the Surround speakers setting in the Speaker size, then this setting will not appear.

SURR BACK EFFECT : Set the effect level of the Surround Back speaker between –3 and +3 level in 1 level interval .

•If “None” was selected for the Surround back speakers setting in the Speaker size, then this setting will not appear.

CENTER EFFECT : Set the effect level of the center speaker between –3 and +3 level in 1 level interval .

•If “None” was selected for the Center speaker setting in the Speaker size, then this setting will not appear.

SUB W EFFECT : Set the effect level of the subwoofer speaker between –3 and +3 level in 1 level interval .

•If “None” was selected for the Subwoofer speaker setting in the Speaker size, then this setting will not appear.

Note:

•These effect level set up are available only while in HALL, MATRIX, MOVIE, CSII, Multi CH. STEREO.

If you finish the setup in this item, move cursor to “MAIN” with Up or Down cursor buttons and press OK button.

34