Matrox Electronic Systems 4SIGHT-M Custom power supply

52 Chapter 4: Installing the Matrox 4Sight-M motherboard in a custom chassis

Custom power supply

The power connector on the stand-alone Matrox 4Sight-M motherboard is a 4-pin

locking connector.

Voltage requirements for each pin are given below.

Pin Power supply (V) Max. voltage (V) Min. voltage (V) Maximum current1 (A)

1. The maximum current capacity of each pin is 7 A.

1 12-24 24 12 7

2GROUND

3 12-24 24 12 7

4GROUND

Rear of motherboard

Pin 1 Pin 2

Pin 3 Pin 4

MATROX IMAGING est distribué par TECHWAY - www.techway.fr - info@techway.fr - +33 (0)1 64 86 58 30

Contents

Main Page Contents Part 1: Operating your Matrox 4Sight-M unit Chapter 1: Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Chapter 2: Connecting peripherals to the unit . . . . . . . . . . . . . . 23 Part 2: Customizing the motherboard Chapter 3: Adding devices to the Matrox 4Sight-M motherboard 39 Part 3: Reference material for all users Chapter 5: Matrox 4Sight-M hardware reference. . . . . . . . . . . . . 55 Part 4: Appen dices Appendix A: BIOS reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Appendix B: Technical reference . . . . . . . . . . . . . . . . . . . . . . . . 109 Page Using this manual Page Page Page Page Hardware components Page 16 Chapter 1: Before you begin Mass storage Chassis Matrox 4Sight-M components and connectors Optional components Inspecting your Matrox 4Sight-M package Motherboard-only version Additional components You might have purchased one or more of the following additional components to complete your unit: Operating your Matrox 4Sight-M unit Page Page Page Connecting display devices Page Page Connecting a USB mouse, keyboard, or printer Connecting other USB devices Networking connections Page Connecting video input devices Page Page Page Connecting devices to the serial port Connecting devices to the auxiliary I/O interface Connecting a stereo audio device Page Page Page Page Introduction Removing the Matrox 4Sight-M chassis Front panel Back panel Page Connecting a hard disk or CD drive Page Page Connecting a PC/104-Plus board Removing and installing memory Page Page Custom chassis Custom fan Custom power supply Page Page Page 56 Chapter 5: Matrox 4Sight-M hardware reference Motherboard Intel North Bridge (GMCH) 855 GME with integrated graphics Embedded Intel Celeron M or Pentium M Intel ICH4 (82801DB) Processing Page Memory Display Mass storage BIOS Networking I/O interfaces I/O interfaces 63 UPTO 4000 FT Connecting your Matrox 4Sight-M unit to a multidrop network Four-wire multidrop network SUPPORTED BY MATROX4SIGHT-M 64 Chapter 5: Matrox 4Sight-M hardware reference Two-wire multidrop network UP TO 4000 FT Page PC/104-Plus interface Power supply, fan, and chassis Page Chassis Page Page Page Page Page Introduction The BIOS Setup utility Page Page The Item Specific Help window Main menu Page Page Page Page Page Page Page Page Advanced menu Page Page Page Intel menu Page Page Page Power Menu Boot menu Expanding and collapsing device types Page Page Exit menu Overriding the device sequence Page BIOS messages and diagnostic codes Page Page Page Page Page Page Motherboard A four-pin power connector. The voltages that can be drawn are outlined in the following table: Rear of motherboard Pin 1 Pin 2 Pin 3 Pin 4 Memory Hard drive Power supply Chassis Fan Battery Auxiliary I/O interface Pinouts of front panel connectors Page Analog VGA connector DVI-compliant digital VGA connector ("DVI-I") Page Auxiliary I/O connector ("Aux. I/O") 31 15 44 1 16 30 Pinouts of back panel connectors Top serial port connector (RS-232 standard only): Bottom serial port connector: Page Matrox Meteor-II /Multi-Channel Matrox Meteor-II /Camera Link Page Page Digital video input connectors ("Digital Video in") Page Page Camera Link connectors Pinouts of internal connectors and dip switches Internal ATA 44-pin connector Front of computer Page Internal ATA 40-pin connector 240 39 1Front of computer Page Internal connector for the parallel interface The internal connector for the parallel interface is a 26-pin, IDC male connector. The pinout of this connector is outlined in the following table: Page 1234 on Creating custom cables off Unit Reliability Prediction Mean time between failure (MTBF) The following table outlines the mean time between failure for modules on Matrox 4Sight-M: Page Page Page Page Page Page Page Page Page Page Page Page Index Page Page Page Regulatory Compliance FCC Compliance Statement Industry Canada Compliance Statement EU Notice (European Union) Page Product support Page Product Assistance Request Form