Troubleshooting Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.
•Selector” button is pressed, the Main relay will be toggled (either from “on” to “off” or from“ off” to “on”).
•When the “Rotary Cycle Selector” is set to “Normal” and the “Rotary Cycle Selector” button is pressed, the hot water valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.
•When the “Rotary Cycle Selector” is set to “Wrinkle Control” and the “Rotary Cycle Selector” button is pressed, the cold water valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.
•When the “Rotary Cycle Selector” is set to
“Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.
•When the “Rotary Cycle Selector” is set to “Hand Wash” and the “Rotary Cycle Selector” button is pressed, the pre wash valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.
•When the “Rotary Cycle Selector” is set to “Quick Wash” and the “Rotary Cycle Selector” button is pressed, the drain pump will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output.
•Pressing the “Delay” switch pad will turn on the motor and the “Delay” LED. This output and the LED will remain on until the “Delay” switch pad is pressed again to turn off the output. When activated, the machine will tumble for 5 seconds in the CW direction, pause for 2seconds, tumble in the CCW direction for 5 seconds, pause for 2 seconds; repeating this pattern until “ Delay” button is pressed again to turn off the tumbling. Note that all tumble speeds are assumed to be 45 rpm.
•Pressing the “Chime” switch pad will unlock the door and turn on the all the LED’s above
the “Chime” button. This output will attempt to unlock one time, if safe to do so.
•Pressing the “Temperature” switch pad will lock the door and all the Temperature LED’s will turn ON. Pressing the “Chime” button will unlock the door and the all the Chime LED’s will turn ON.
•When the “Rotary Cycle Selector” is set to
“Colors” and the “Rotary Cycle Selector” is pressed, the bleach valve and the cold water valve will be turned on to check the fabric softener fill. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.
•When the “Rinse & Spin” keypad is pressed, the Heater will be turned on if the water level is above the Heater Safety Level. If the water level is below the Heater Safety Level, a warning beep will be given and the heater will not be turned on. The Heater output will remain on until the “Rinse & Spin” keypad is pressed again to turn off the output.
Selection | Component | Function | |
Rotary cycle selector |
|
| |
set to Super Wash. | Main Relay | On to Off or | |
Press Rotary | Off to On | ||
| |||
Selector Knob. |
|
| |
Rotary cycle selector |
| 1st press valve | |
set to Normal. Press | Hot Water | on. 2nd press | |
Rotary Selector | Valve | valve off. | |
Knob. |
|
| |
Rotary cycle selector |
| 1st press valve | |
set to Wrinkle | Cold Water | on. 2nd press | |
Control. Press | valve off. | ||
Valve | |||
Rotary Selector |
| ||
|
| ||
Knob. |
|
| |
Rotary cycle selector |
| 1st press valve | |
set to Delicates. | Bleach Valve | on. 2nd press | |
Press Rotary | valve off. | ||
| |||
Selector Knob. |
|
| |
Rotary cycle selector |
| 1st press valve | |
set to Hand Wash. | Pre Wash | on. 2nd press | |
Press Rotary | Valve | valve off. | |
Selector Knob. |
|
|
©2005 Maytag Services | 16025909 Rev. 0 | 17 |
