Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20), and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certified for use with L.P. (propane or butane) gases with appropriate conversion. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier.

Conversion must be done by a competent service technician. Gas conversion kit, part number W10233219, is available for purchase from your dealer. Full instructions are supplied with the kit.

Natural gas (France/Belgium):

This dryer is also certified for France/Belgium for use with G20/G25 gases (20 mbar/25 mbar) with appropriate conversion. No attempt should be made to convert this appliance from the gas specified on the gas rating label for use with a different gas without consulting the serving gas supplier.Gas conversion must be done by a qualified gas service technician. Conversion kit, part number (W10181947) is available for purchase from your dealer. Full instructions are supplied with the kit.

Supply line requirements:

Provide a rigid gas supply line to the dryer location. It should be minimum 12.5 mm (1/2") ID. When acceptable to the gas supplier and local codes, 10 mm (3/8") ID rigid supply line may be used for lengths under 6.1 m (20’). Pipe-joint compounds resistant to the action of L.P.gas must be used.

Gas connection to the dryer itself should be made by means of a flexible gas hose suitable for the appliance and gas category in accordance with national installation regulations. If in doubt, contact the gas supplier. It should be minimum 10 mm (3/8") ID.

A means of restraint should be used between the appliance and the wall to prevent straining of the rigid gas supply when the appliance is moved. An appropriate length of chain and a wall hook is recommended.

The dryer gas inlet connection is a 3/8" NPT thread. An adapter is supplied for conversion to standard ISO.228-1 thread (3/8" BSP).

Check for leaks by using an approved noncorrosive leak- detection solution. Bubbles will show a leak. Correct any leak found. A pressure measurement tapping is provided on the gas valve within the dryer, accessible after removal of the lower front panel.

The dryer must be disconnected from the gas supply piping system during any pressure testing of that system.

Venting Requirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

Adequate ventilation has to be provided to avoid the backflow of gases into the room from other fuel-burning appliances, including open fires (i.e. available airflow into the room should match airflow out from the room).

The design of the flue system should be such that any condensate formed when operating the dryer from cold shall either be retained and subsequently re-evaporatedor discharged.

The dryer vent must not be discharged into a flue which

is used for exhausting fumes from appliances burning gas or other fuels, chimney, wall, ceiling, or a concealed space of a building.

Do not use an exhaust hood with a magnetic latch.

Do not install flexible metal vent in enclosed walls, ceilings, or floors.

102 mm (4") heavy metal vent and clamps must be used.

Use clamps to seal all joints. Vent must not be connected or secured with screws or other fastening devices which extend into the interior of the vent and catch lint. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

An exhaust hood should cap the vent to prevent rodents and insects from entering the home or business.

Exhaust hood must be at least 30.5 cm (12") from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, or bushes).

If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or flexible metal vent.

7

Page 7
Image 7
Maytag MDG17MN Venting Requirements, Natural Gas, Natural gas France/Belgium, Supply line requirements

MDG17MN specifications

The Maytag MDG17MN is a robust and reliable gas dryer that caters to the laundry needs of households, delivering exceptional performance and efficiency. With its sleek design and user-friendly interface, it seamlessly blends into any laundry room while providing powerful drying capabilities.

One of the key features of the MDG17MN is its impressive capacity, which allows for ample drying space to handle large loads of laundry. This makes it an ideal choice for families or individuals who regularly deal with bulky items like bedding or towels. The dryer is equipped with a high-performance gas burner that ensures rapid heat-up times, reducing overall drying duration.

The MDG17MN comes with a range of drying cycles tailored to meet varying fabric care needs. From heavy-duty settings for towels and jeans to delicate cycles for finer fabrics, the dryer offers versatility for different laundry requirements. Additionally, the inclusion of moisture sensing technology enhances drying efficiency by detecting moisture levels in the load, automatically adjusting drying times and preventing over-drying, which helps to maintain the quality of garments.

An important consideration for any appliance is energy efficiency, and the MDG17MN excels in this aspect. By utilizing an advanced gas heating system, it consumes less energy compared to traditional electric dryers while still delivering powerful performance. This not only helps to lower energy bills but also makes it a more environmentally friendly option.

The design of the MDG17MN places an emphasis on user convenience. An easy-to-use control panel features straightforward settings, making it simple to select the desired drying cycle. The dryer also comes with a sturdy lint screen that can be easily accessed and cleaned, promoting optimal airflow and maintaining performance.

Durability is another hallmark of the Maytag brand, and the MDG17MN is no exception. Constructed with high-quality materials, this dryer is built to withstand regular use while ensuring longevity. In summary, the Maytag MDG17MN gas dryer combines capacity, efficiency, advanced drying technologies, and user-friendly features, making it a commendable choice for effective laundry management in any home.