SECTION 3 - SERVICING COMPONENTS

Appendix - Instructions for Service Kit 39733 -

High Limit Conversion Kit for PS300, 310, 350 & 360 Ovens, 5/99

B. INSTALLATION

WARNING

BEFORE PERFORMING ANY SERVICE WORK, THE GAS SUPPLY (IF SO EQUIPPED) AND THE ELECTRICAL SUPPLY TO THE OVEN MUST BE TURNED OFF.

1.Open the machinery compartment and control compartment access panels.

2.Locate the high limit thermo bulb/capillary assembly. Its location is shown in Figure 2. Loosen the set screw that holds the assembly in place. Remove the thermo bulb/capillary assembly from the mount- ing tube.

3.Disconnect the wires (2 for the Type 54 control, 4 for the Type 55 control) from the terminals of the United Electric control. Bundle the loose wires together, and allow them to hang loose for later reconnection.

4.Remove the mounting screws that hold the United Electric high limit control in place. Then, remove and discard the high limit control and its mounting screws.

5.Position the new high limit control in place on the left wall of the control compartment, as shown in Figure 3. When positioning the control:

Ensure that the control is positioned AT LEAST 1” (25mm) back into the compartment to allow the compartment door to close.

Ensure that additional space is left underneath the control for the reset switch.

NOTE: Instead of holding the high limit control in place, you may use the dimensions provided in Figure 4 to determine the location of the control and its mounting holes.

6.Mark the locations of the two mounting holes for the high limit control. Then, drill the holes using a 3/16” drill bit.

7.Secure the high limit control in place using the kit-supplied 6-32 x 1-5/8” screws and 6-32 nuts.

8.Position the bracket for the reset switch on the left wall of the control compartment, as shown in Figure 3. Note that the face of the bracket with the large, circular switch-mounting hole should face YOU. Also, the bracket should be positioned AT LEAST 3” (75mm) back into the compartment to allow the door to close.

9.While holding the bracket in place, mark the locations of the two mounting holes. Then, remove the bracket and drill the holes using a 3/16” drill bit.

10.Secure the bracket to the panel using the kit-supplied 6-32 x 1/4” screws and 6-32 nuts. DO NOT INSTALL THE RESET SWITCH INTO THE BRACKET AT THIS TIME.

11.Insert the kit-supplied thermocouple into its mounting sleeve. Position the sleeve so that the mounting hole is at the base of the thermocouple, not the tip. See Figure 5.

12.Insert the thermocouple and mounting sleeve into the original mounting tube. The set screw opening in the sleeve should align with the set screw hole on the side of the mounting tube.

Push the thermocouple into the opening until its base seats firmly on the mount. See Figure 6.

13.Insert the thermocouple’s set screw into the hole on the side of the mounting tube. Tighten the set screw to hold the thermocouple and sleeve in place.

14.Thread the thermocouple’s shielded cable into the electrical compartment. Coil the free end of the cable and fasten it with the kit-supplied nylon wire tie. Be sure to leave enough free cable to reach the new high limit control.

Page 2 of 8

47

Page 48
Image 48
Middleby Marshall PS570, PS360, PS200, PS555, PS220, PS224 PS310 manual Installation

PS224 PS310, PS220, PS555, PS200, PS360 specifications

The Middleby Marshall PS555 is a standout commercial pizza oven renowned for its performance, efficiency, and advanced technologies. Designed with the modern pizzeria in mind, the PS555 delivers exceptional cooking results while maximizing energy efficiency and throughput.

One of the key features of the PS555 is its innovative cooking technology, which incorporates both convection and radiant heat. This unique combination ensures that pizzas are cooked evenly and quickly, achieving a perfectly crispy crust and evenly melted cheese every time. The oven’s high-speed air impingement system accelerates cooking times, allowing pizzerias to serve more customers in less time without compromising quality.

The PS555 is designed with a spacious cooking chamber that can accommodate multiple pizzas simultaneously. With its ability to fit pizzas up to 18 inches in diameter, the oven is ideal for establishments with high demand. Additionally, the adjustable conveyor speed allows operators to customize the cooking time based on their specific menu items, enhancing versatility and productivity.

Energy efficiency is a hallmark of the Middleby Marshall PS555. The oven utilizes advanced insulation materials to minimize heat loss, ensuring that it operates at optimal temperatures while consuming less energy. This efficiency not only reduces operating costs but also contributes to a more sustainable kitchen environment.

User-friendly controls make it simple for operators to manage the cooking process. The PS555 features digital controls with programmable settings, enabling quick adjustments to temperature and cooking time. This ensures consistent quality across different shifts and helps maintain product standards while simplifying staff training.

Durability is another defining characteristic of the PS555. Built with high-quality materials, the oven is designed for heavy use in busy commercial kitchens. Its stainless steel construction ensures resistance to wear and tear, making it a worthwhile investment for any pizzeria.

In summary, the Middleby Marshall PS555 pizza oven is a high-performance piece of equipment that combines advanced cooking technologies, efficiency, and durability. Its ability to deliver consistently excellent results while streamlining operations makes it an essential asset for any pizza business aiming to enhance its productivity and customer satisfaction.