Miller Electric Big Blue 400 KX instruction

11-7. Approximate Power Requirements For Contractor Equipment

Contractor	Rating	Starting Watts	Running Watts

Hand Drill	1/4 in	350	350
	3/8 in	400	400
	1/2 in	600	600
Circular Saw	6-1/2 in	500	500
	7-1/4 in	900	900
	8-1/4 in	1400	1400
Table Saw	9 in	4500	1500
	10 in	6300	1800
Band Saw	14 in	2500	1100
Bench Grinder	6 in	1720	720
	8 in	3900	1400
	10 in	5200	1600
Air Compressor	1/2 HP	3000	1000
	1 HP	6000	1500
	1-1/2 HP	8200	2200
	2 HP	10500	2800
Electric Chain Saw	1-1/2 HP, 12 in	1100	1100
	2 HP, 14 in	1100	1100
Electric Trimmer	Standard 9 in	350	350
	Heavy Duty 12 in	500	500
Electric Cultivator	1/3 HP	2100	700
Elec. Hedge Trimmer	18 in	400	400
Flood Lights	HID	125	100
	Metal Halide	313	250
	Mercury	1000
	Sodium	1400
	Vapor	1250	1000
Submersible Pump	400 gph	600	200
Centrifugal Pump	900 gph	900	500
Floor Polisher	3/4 HP, 16 in	4500	1400
	1 HP, 20 in	6100	1600
High Pressure Washer	1/2 HP	3150	950
	3/4 HP	4500	1400
	1 HP	6100	1600
55 gal Drum Mixer	1/4 HP	1900	700
Wet & Dry Vac	1.7 HP	900	900
	2-1/2 HP	1300	1300

OM-4423 Page 50

Image 56

Miller Electric Big Blue 400 KX manual Approximate Power Requirements For Contractor Equipment

Contents

OM-4423 215 178N ProcessesDescription File Engine Drive From Miller to You Table of Contents − Maintenance & Troubleshooting 8-1. Routine Maintenance Decrot6/05 DirectivesStandards Sound Level Information Decrotsound1/05 Symbol Usage Arc Welding Hazards Engine Hazards Compressed Air Hazards Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïe ’AIR Comprimé peut provoquer des blessures ’EMPLOI Excessif peutLE Surchauffement peut endom- mager le moteur électrique LES Étincelles Volantes risquent de provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférences Pour les moteurs à essencePour les moteurs diesel Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone Std − Definitions− 50 h Std Manufacturer’s Rating Label Symbols And Definitions Dimensions, Weights, And Operating Angles − SpecificationsWeld, Power, And Engine Specifications Stick Mode MIG ModeTIG Mode Volt-Ampere Curves Curve shows typical fuel use under weld or power loads Exceeding duty cycle can damage unit and void warrantyFuel Consumption Duty Cycle And Overheating AC Generator Power Curve Ac power curve shows the gen- erator power in amperes − Installation Installing Welding Generator Mounting Welding Generator Stop engine and let cool Installing Exhaust PipeTools Needed 1/2 Activating The Dry Charge Battery If Applicable Connecting The BatteryDo not overfill battery cells Connect Negative − Cable Last Coolant Recovery Tank Engine Prestart ChecksFuel Do not use gasoline. Gasoline will damage engine Oil Connecting To Weld Output Terminals Stick and TIG WeldingMIG and Fcaw Welding Stop engine Selecting Weld Cable Sizes 150 ft 200 ft 250 ft350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Stop engine before Connecting To Remote 14 Receptacle RC14 Socket Front Panel Controls See Section Stop Description Of Front Panel Controls See Section Process/Contactor Switch On CC/CV Models Process/Contactor Switch Settings Lift-ArcStart Procedure Lift-Arc Start Method TouchDo not Strike Like a Match Lift-Arc t TIG Remote Voltage/Amperage Control − Operating Auxiliary Equipment Volt Receptacles − Maintenance & Troubleshooting Routine Maintenance Maintenance Label Servicing Air Cleaner By the warrantyTo clean air filter Do not clean housing with air hose Servicing Engine Cooling System Inspecting And Cleaning Spark Arrestor MufflerStop engine and let cool. Reinstall cleanout plug Adjusting Engine Speed On Standard Models Maximum Servicing Fuel And Lubrication Systems Stop engine and let cool After servicing, start engineTo change oil and filter To replace primary canister fuel filter Press button to reset breaker Overload Protection Checking Generator Brushes Replace Damaged Brushes Help 25 Display Voltmeter/Ammeter Help DisplaysHelp 20 Display Welding TroubleshootingStandard Generator Power Engine Check for obstructed throttle solenoid − Electrical Diagrams Circuit Diagram For Welding Generator 221 499-B Welding Generator − RUN-IN ProcedureWetstacking Run-In Procedure Using Load Bank Procedure at less thanStop engine Do not touch hot exhaust From flammables Do not Perform Run-In Procedure Using Resistance Grid Bank/gridFrom flammables Do not perform run-in Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Amperes x Volts = Watts Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts Amperes − Parts List 103 − −5 104 − −3 96− −2 102 101 100 71− −4 3031 5756 Dia Part Description Quantity Mkgs Dia Part Description Quantity 213600 Panel, Front w/Components Panel, Front w/Components -1Item FUEL/HM Control Panel Generator Generator -1Item Rectifier Assembly Wiring Harnesses Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s