Notes
owners manual
SUBWOOFER PLACEMENT |
| Rear Panel |
|
The placement of your new MIRAGE® subwoofer is critical to its |
| 6. Power Mode – This switch |
|
performance. The three most common locations include: in the corner |
| can be set to either On, Off |
|
| or Auto. If the switch is in |
| |
of the room (which can result in a boomy or exaggerated low |
|
| |
| the Off position, the |
| |
frequency response), placement along one wall but out of the corner |
|
| |
| subwoofer will not power |
| |
(moderate bass performance with increased fidelity over corner |
|
| |
| up. If the switch is in the On | 6 | |
placement), or alongside a front speaker (creating a better blend with |
| ||
| position, it will constantly | ||
the front speaker, but sacrificing overall volume). Experimentation with |
|
| |
| remain on. If the switch is |
| |
subwoofer placement is highly encouraged, as slight adjustments can |
|
| |
| set to the Auto position, |
| |
create large benefits in sound reproduction. To further test subwoofer |
|
| |
| when a signal is present the |
| |
placement, install the subwoofer temporarily in your main listening |
|
| |
| subwoofer will turn on and | 7 | |
position and while playing a familiar piece of music, walk around the |
| ||
| will automatically turn off | ||
listening room until you find the best sounding position. This is a |
|
| |
| several minutes after a signal |
| |
possible location for the subwoofer to be placed. |
|
| |
| is no longer present. |
| |
|
|
| |
TERMINOLOGY AND CONTROLS |
| 7. Sub In – This input is an RCA | 8 |
| type mono input. | ||
|
| 8. |
|
|
|
| |
1 |
| speaker connectors. The |
|
|
| ||
|
| designed to be used on |
|
2 |
| receivers or amplifiers that |
|
| do not incorporate any RCA |
| |
|
| type subwoofer outputs. If |
|
3 |
| your receiver is equipped |
|
| with an RCA type subwoofer |
| |
|
|
| |
|
| output, these speaker level inputs should not be utilized. |
|
4 |
|
|
|
5 |
| CONNECTING YOUR |
|
| MIRAGE SUBWOOFER |
|
Front Panel
1.Subwoofer Level Control - This knob can be adjusted to control the level of output from your subwoofer. The level chosen should allow the subwoofer to blend its output with that of the rest of your audio system.
2.Status Indicator – The LED found on the front panel will illuminate when the subwoofer is connected to an AC source and the unit is active. The LED will display in red when the unit is plugged in but is not receiving a signal and will display green when the unit is active.
3.Frequency Control – This control allows for the adjustment of the
4.Phase Control – This switch allows for the adjustment of the phase of the subwoofer, in relation to the speakers used in your system, either 0 degrees or 180 degrees.
5.Filter Mode – This switch allows for the selection of either Filter On or Filter Off. (Please see the connections section for suggestions on which mode is appropriate for your installation).
Caution:
All power should be turned off to your system before any connections are made. Careful attention should be taken to ensure that all electronic components are not connected to an AC source. Not doing so could result in potential damage to the system.
There are two mutually exclusive methods to connect your subwoofer to your receiver.
Method 1 – RCA – For Home Theater or LFE Applications
1.On the rear of the receiver there should be a single RCA type jack marked “Subwoofer Out”. Connect a single RCA cable from that jack to the RCA Sub In (#7) on the rear of the subwoofer. A standard male to male RCA cable is needed.
2.After connecting the single low level Sub In (#7) connection, plug your MIRAGE® subwoofer into an AC outlet. Do not use the AC outlet on the rear of your receiver.
30
3