Mitsubishi Electronics AG-150A 6-2 Night Mode Schedule

33

6-2 Night Mode Schedule

Click on [Function2]-[Night Mode Schedule] in th e menu to ope n the night m ode schedule screen and m ake

necessary settings to switch the outdoor unit operation m ode to th e n ight m ode (low-noise operation), and set

the night mode time interval.

Use this mode when low-noise operation of the outdoor uni t is preferable during night.

Note: Make this setting only when all the units operate normally. When connection error occurs at the indoor or the outdoor unit,

night mode target units may not be displayed normally.

Note: The noise level to be reduced varies depending on the unit model.

Note: If the user logs in as a building manager, the operations may be prohibited.

(1) Set the time interval in [Night mode start time] and [Night mode end time].

Note: When the starting time and the ending time is the same, night mode operation will always be performed.

(2) Select the outdoor unit, which performs night mode oper ation from [Target outdoor units].

Note: M-NET address numbers for each outdoor unit are displayed in the target unit field.

(3) Click [Save Settings] to send setting data to the AG -150A.

Save settings

Send setting data to AG-150A.

Refresh

Read setting data from AG-150A.

Night mode start time

Click to set the start time. Night mode end time

Click to set the end time

Target outdoor units

Click to select the outdoor unit,

which performs night mode

control.

Contents

Main Air-conditioner Network System Centralized Controller Model: AG-150A operation. Keep this manual for future reference. (Web browser for Initial Settings) 1 Introduction .........................................................................1 2 Setting the Operating Env ironment......................................2 1 Introduction 1-1 Conventions Used in This Manual 1-2 Computer Requirements 1-3 Notes on using AG-150A with the integrated centralized control software (TG-2000A) 2 Setting the Operating Environment 2-1 Setting the PC IP Address Page 2-2 Setting the Web Browser 2-2-1 Not connecting to the Internet 2-2-2 Connecting to the Internet using a dial-up connection 2-2-3 Connecting to the Internet using a proxy server (Using an existing LAN) 3 Performing Operations 3-1 Logging in on the AG-150A 3-1-1 Logging in on the AG-150A http:// [IP address of the AG-150A]/g-50 /administrator.html 3-1-2 Encrypting the communication data and login on the AG-150A /administrator.html Page 4 Initial Settings 4-1 Setting the Current Date and Time 4-2 Setting the Basic Information and External Input Functions 4-2-1 AG-150A Unit Setting 4-2-2 M-NET Setting 4-2-3 Network Setting 4-2-3-1 Settings for when the AG-150A is connected to a dedicated LAN 4-2-3-2 Settings for when the AG-150A is connected to an existing LAN 4-2-4 External Input Setting Page 4-2-5 Setting the Display Format 4-3 Group Setting 4-3-1 Setting the Group Name 4-3-2 Registering air conditioner or hot water supply units in the group 4-3-3 Registering general equipment in the group 4-4 Interlocked Setting 4-5 Block Setting 4-5-1 Registering a block name 4-5-2 Registering a group in a block 5 Functions 1 5-1 Error mail reports/E-mail communication 5-1-1 Entering the E-Mail Information for the AG-150A 5-1-2 Setting the Mail Server Information 5-1-3 Setting the Error Mail Destinations 5-1-4 Setting the Addresses of the Recipient 5-1-5 Mail format 5-2 Energy-Save Control and Peak Cut Control 5-2-1 When Demand Controller Method is used 5-2-2 When Electric Amount Count PLC Method (Amount Count Software) is used 5-2-3 When PI Controller Method is used 5-2-4 When Remote AG-150A Method is used 5-2-5 When From external system Method is used 5-2-6 Setting the Outdoor Unit Control Method (All methods) 5-2-7 Setting the Indoor Unit Control Method (All methods) 5-3 Settings for measurement 5-3-1 Registering AI controllers for temperature/humidity sensors 5-3-2 Adjusting the measured temperature/humidity values 5-3-3 Registering PI controllers for measurement by meters 5-3-4 Setting the trend data format 5-3-5 Setting the destination to which an error mail is sent 5-3-6 Setting the destination to which temperature/humid trend data mail is sent 6 Functions 2 6-1 Limiting the Set Temperature Operating Range 6-2 Night Mode Schedule 6-3 System-Changeover of Y series 7 Functions 3 7-1 External Temperature Interlock 7-2 Night setback control 8 User Setting Page 9 Registering a License for Optional Function