Mitsubishi Electronics PAC-YG63MCA instruction manual Dip Switch Functions

9Dip Switch Functions

SW		Supported		Function		OFF	ON	Remark
		Channel
SW01	1			Selection of the input to use		No	Yes	Specify whether to use the channel 1 input terminal.
						4 to 20 mADC/	0 to 10 VDC	Set the type of analog input for channel 1 (1).
	2					1 to 5 VDC
				Selection of the analog input			detection	* This should also be set in accordance with the selection
						detection
				type (1)				of analog input type (2) (SW11-1 and 2).
							Pt100
	3					–		* The setting of SW01-2 is disabled when SW01-3 is ON.
							detection
		Channel 1
	4			Unused				Set to OFF
	5			Selection of upper/lower limit		No	Yes	Specify whether to use channel 1 upper/lower limit
				alarm interlock output use				alarm interlock output.
	6			Unused				Set to OFF
	7			Unused				Set to OFF
	8			Unused				Set to OFF
SW02	1			Selection of the input to use		No	Yes	Specify whether to use the channel 2 input terminal.
				Selection of the analog input		4 to 20 mADC/	0 to 10 VDC	Set the type of analog input for channel 2 (1).
	2					1 to 5 VDC		* This should also be set in accordance with the selection
				type (1)			detection
						detection		of analog input type (2) (SW12-1 and 2).
	3			Unused				Set to OFF
	4	Channel 2		Unused				Set to OFF
	5			Selection of upper/lower limit		No	Yes	Specify whether to use channel 2 upper/lower limit
				alarm interlock output use				alarm interlock output.
	6			Unused				Set to OFF
	7			Unused				Set to OFF
	8			Unused				Set to OFF
SW03	1	Measurement	data backup interval			SW03-1	SW03-2
		1-minute interval: (2 hours worth)				OFF	OFF	Set to back up measurement data to the fixed memory.
		2-minute interval: (4 hours worth)				OFF	ON
	2	5-minute interval: (10 hours worth)				ON	OFF	Excess past data will be erased.
		10-minute interval: (20 hours worth)				ON	ON
	3	Unused						Set to OFF
	4	Unused						Set to OFF
	5	Unused						Set to OFF
	6	Unused						Set to OFF
	7	Unused						Set to OFF
	8	Unused						Set to OFF
SW06						(Address 10s)		An address from 01 to 50 can be set.
						0 to 9 (decimal)
		M-NET address						Set an address that is not the same as that of another
						(Address 1s)
SW07								unit.
						0 to 9 (decimal)
SW08	1	Unused						Set to OFF
	2	Unused						Set to OFF
	3	Unused						Set to OFF
	4	Unused						Set to OFF
	5	Unused						Set to OFF
	6	Unused						Set to OFF
SW09	1	Unused						Set to OFF
	2	Unused						Set to OFF
SW11	1			Selection of analog input type (2)		SW11-1	SW11-2
				0 to 10 VDC detection	:	OFF	OFF	Set the type of analog input for channel 1 (2)
		Channel 1		1 to 5 VDC detection	:	OFF	ON
								*1: This setting is not necessary when SW01-3 is ON.
	2			Setting not possible	:	ON	OFF
				4 to 20 mADC detection:		ON	ON
SW12	1			Selection of analog input type (2)		SW12-1	SW12-2
				0 to 10 VDC detection	:	OFF	OFF
		Channel 2
				1 to 5 VDC detection	:	OFF	ON	Set the type of analog input for channel 2 (2)
	2			Setting not possible	:	ON	OFF
				4 to 20 mADC detection:		ON	ON

Set the dip switches for function selection according to the system to be used.

At factory default, the SW01, SW02, SW03, SW08, and SW09 dipswitches are all set to OFF; the SW11 and SW12 dipswitches are both set to ON, and the M-NET address is set to 01.

Be sure to turn off the power before changing switch settings.

12