Mitsubishi Electronics WD-52528, WD-62527, WD-62528 manual Troubleshooting

Troubleshooting, continued

	Problem	Possible Solution
41.	The IEEE 1394 Device is not listed in the Device	• The device is unchecked in the Review screen. Select the
	Selection menu.	NetCommand menu. Through Review, verify the device is checked.
		• The IEEE 1394 plug is disconnected or loose.
		• The IEEE 1394 Device has not been powered On. Turn on.
		• The device has not been discovered.
		• The device is not an Audio/Video device
42.	The IEEE 1394 device cannot be selected.	The device may be busy, either recording or a peer-to-peer connection
		has been established. Cancel the recording or peer-to-peer
		connection.
43.	DEVICE MENU button does not display a menu.	• The IEEE 1394 device does not provide a menu.
		• The TV cannot support IEEE 1394 menus. See page 53.
44.	All IEEE 1394 devices disappear.	• The connected devices must not be in a loop that returns to the TV.
		Make sure a device is connected at the end.
		• Disconnect all the cables and devices from the TV. Replace them one
		by one to locate the problem device or cable.
		• Use System Reset (front control panel).
45.	Cannot rediscover a deleted IEEE 1394 device	• The device has been disconnected. Plug it in.
		• The device is unchecked in the Review screen. Select NetCommand
		from the Main menu, then select Review. Check the device.
		• Remove IEEE 1394 plug. Go to the Edit NetCommand menu.
		Delete the IEEE 1394 device. Plug the device in again so it can be
		discovered again.
46.	An IEEE 1394 device has been plugged in but	• The IEEE 1394 connection to the TV or another device is not secure
	does not appear in the Device Selection menu	or is loose.
	(not discovered).	• The IEEE 1394 device is not powered on.
		• A device in the IEEE 1394 chain is not powered on—turn on all the
		devices.
		• The device discovery can take as long as a minute to initiate.
		• IEEE 1394 cable is too long (maximum of 15 feet between devices).
		• The IEEE 1394 device uses an incompatible protocol and will not be
		discovered
47.	Cannot record to or from the IEEE 1394 device,	• To initiate a recording to IEEE 1394 device press the REC key. The
	including dubbed recordings.	Record menu displays allowing setup of the recording.
		• The source device for the recording is not powered on.
		• When dubbing, the destination device for the recording is not
		powered on.
		• The wrong medium, (analog tape for digital recording, or digital tape
		for the analog recording) is in the device.
		• Either the program is copy protected, or if there are multiple
		subchannels and one of the programs (not necessarily the program
		requested) is copy protected.
		• The program has already been recorded once and the copy
		protection only allows one recording.
		• Unapproved source device for copy protected material.
		• The recording device can not decode the copyright signal included in
		the signal source (try another device if available).
		• The playing device (for dubbing) does not support copyrighted
		material.
		• Source for recording is copyrighted.
		• Too many IEEE 1394 devices in network. Insufficient bandwidth
		available. Disconnect unused devices.
		• Source Device has higher speed (S 400) than record device. If
		possible, reverse devices, play in the slower device and record in the
		faster device.
48.	Cannot control the IEEE 1394 device from the	• Device may not support the command.
	Transport Menu.	• Selected function is gray (such as Record for a DVD, which does not
		support the Record function).
49.	When ChannelView™ list is displayed,	Available information is sent from the broadcaster or cable provider. No
	information appears incomplete.	other data is available.

Chapter 6. Special Features 101