Mitsubishi Electronics WD-62528, WD-62527 Connecting External Devices and NetCommand Setup, Chart

Connecting External Devices and NetCommand® Setup

NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver back panels match the NetCommand setup that is displayed on-screen.

To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio and video) and to the A/V receiver (audio) as shown in the figure below.

EFWJDF
UP
CF

DPOOFDUFE

WJEFP
BOE
TUFSFP

BVEJP
DBCMFT

*3
&NJUUFST

TUFSFP
BOEPS

EJHJUBM
BVEJP
DBCMFT

TV

FJUIFS
BOBMPH
TUFSFP
PS

EJHJUBM
DPBYJBM
BVEJP
DBCMFT

"7

SFDFJWFS

The following charts show which preset inputs you should use on the TV and A/V receiver. Chart 1 shows TV inputs.

Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand. Only audio should be connected to the A/V receiver.

Chart 1

Default Device Audio and Video Outputs to TV Inputs

Cable for CableCARD™ Service

ANT-1

Antenna/Cable (digital/analog)

ANT-1 if primary viewing source,

ANT-2 if secondary viewing source

Cable box

Component-1

VCR

Input-1

Satellite Receiver

Input-2

Camcorder

Input-3 (on front panel)

DVD Player

Component-2

Chart 2

Mitsubishi 1

Mitsubishi 2

Bose

Denon

Integra

Kenwood

Marantz

Pioneer 1

Pioneer 2

Rotel

Sony

Yamaha 1

Yamaha 2

Model

Model

Model

Model

Model

Model

Model

Model

Model

Model

Model

Model

Model

M-VR800 &

M-VR900 &

Lifestyle ®28

AVR-2700

DTR-9.1

VR-2080

SR8200

VSX-D557

VSX-9TX

RSX-1065

STR-DE825

RV-X2095

RX-V2200

M-VR1000

M-VR700

Device Audio Output

to

AV Receiver Inputs by Name

VCR

VCR 1

VCR

VCR

VCR-1

Video 1

Video 1

VCR1

VCR/Tape

VCR 1/DVR

Video 2

Video 1

VCR 1

VCR 1

Satellite Receiver

Aux

Cable/DBS

AUX

CD

Video 3

Video 3

DSS

CD

SAT

Video 4

TV/DBS

TV/DBS

D-TV/LD

DVD Player

DVD

DVD

(built-in)

DVDVDP

DVD

Video 4

DVD

LD/SAT

DVD/LD

Video 5

TAPE/MD

CD

DVD

TV Monitor Output

TV

TV

TV

TV/DBS

Video 4

Video 4

TV

DVD/TV

TV

Video 1

DVD/LD

DVD/LD

CBL/SAT

(& Digital Audio)

After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for connecting each device, custom name devices, add devices not included in the presets above or delete devices no longer used. See Edit NetCommand. See Helpful Hints, at the end of this chapter for additional information on device setup.

22 Chapter 2. Connecting