C. Projecting images
Preparation:
• Remove the lens cap.
COMPUTER 1, 2 buttons
POWER button
Main power switch
POWER button 
POWER 
STATUS
AUTO POSITION
COMPUTER button |
|
| KEYSTONE | |
COMPUTER | ENTER | VIDEO | ||
| ||||
|
| MENU | VOLUME | |
ZOOM/FOCUS button |
| ZOOM/FOCUS | LENS SHIFT | |
LENS SHIFT button |
|
|
|
ENGLISH
1.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2.Turn on the power of the connected computer.
3.Press the POWER button.
•It may take about 1 minute for the lamp to light up.
•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.
•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a prod- uct malfunction.
•Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after
•The projector starts warming up when the POWER button is pressed. During the
•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 31.)
4.Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
5.Adjust with the or button to get a fine picture.
6.Select an input source.
•Press the COMPUTER button on the projector or the COMPUTER 1, COMPUTER 2 or
•The input source is switched from COMPUTER 1 to COMPUTER 2 to DVI at every press of the COMPUTER button on the projector.
•The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.
•The COMPUTER, COMPUTER 1, COMPUTER 2 and
•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.
•Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button. (See page 16.)
•When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may flicker. Press the or button on the remote control to reduce flicker, if it occurs.
7.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.
8.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
9.Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the button again to display “ZOOM.”
10.Adjust with the or button to get an approximate size.
11.Press the LENS SHIFT button. “LENS SHIFT” will appear on the display.
12.Press the or button to adjust the vertical position and or button to adjust the horizontal position of the displayed image.
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
•Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
•When you press the ZOOM/FOCUS button or LENS SHIFT button while no signal is supplied, a blue background screen is displayed.
•When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.
