Remote Wall Switch Installation

REMOTE WALL MOUNTED SWITCH

A remote wall switch and up to fifteen (15) feet of 18 Ga. wire may be used with this appliance. Attach the wall switch in a junction box at the desired location on the wall. See Figure 26. Do not extend beyond the wall switch wire

PILOTHI

	OPTIONAL REMOTE
	WALL SWITCH
	ON
ON	RS

length provided.

NOTE: Extended lengths of wire may cause the ﬁreplace not to function properly. Longer length of wire is permitted if the wire is made out of larger gauge (diameter) wire. Always check with local code.

OFF

TH TP

TH/TP

OFF	OFF
OFF
	OPTIONAL REMOTE
	WALL SWITCH
	ON
	OFF

WARNING	Do not connect wall
	Do not connect wall
	switch of heater to a
	110V circuit.

OPTIONAL FAN/BLOWER SYSTEM

CAUTION

Figure 26 - Wiring Diagram for Wall Switch

Electrical connections should only be performed by a qualiﬁed, licensed electrician. Main power supply must be turned off before connecting fans to the main electrical power supply or performing service.

IMPORTANT: Always check local building codes. This installation must comply with local regulations as well as the National Electric Code.

WIRING

1.Before installing the blower, wire the receptacle into an electrical circuit. This should be done before framing the fire- place. Wire with minimum 60ºC wire in accordance with prevailing codes.

2.Remove the external junction box cover by removing the screw from the right side of the outside firebox wall. Junction box was installed at the factory.

3. The junction box cover has a factory installed	WARNING	Before installing the blower, turn off the ﬁreplace and allow to cool.
“romex” style strain relief connector. After		Only a qualiﬁed service person should service and repair the ﬁre-
connecting the wires, route the wire leads		place. A qualiﬁed service person should connect and disconnect
through this connector. Refer to the wiring		the ﬁreplace to gas supply. Follow all local codes.
diagram in Figure 27a.
diagram in Figure 27a.

BEFORE INSTALLING BLOWER

1.Always turn off the gas supply and allow the unit to cool down before proceeding.

2.Clean the inside of the firebox (wall and floor), where the blower and wires will be installed. Make sure the firebox wall and floor are clean and dry before mounting the blower.

NOTE: It is very important to arrange the blower wires and wire assembly so that wires do not come in contact with blower blades or firebox.

INSTALLING BLOWERS

1.Remove screen rod assemblies by lifting rod and pushing back and down to release rod from the three hooks located behind the face of the fireplace on the right, left, and middle.

2.Remove the plate located in front of the glass at the bottom.

3.Rotate the access doors on the right and left side of the glass toward the glass.

4.Remove glass frame by releasing the three latches located at the top of the firebox. Tilt glass away from the unit, lift glass frame up and away from the unit. See Fig. 32.

5.Remove logs.

6.Remove hearth brick, wall brick and rear brick. NOTE: Remove brackets that secure wall brick.

73D0024

KHLDV SERIES specifications

The Monessen Hearth KHLDV Series is a standout line of direct vent gas fireplaces designed to elevate both the aesthetics and functionality of residential spaces. Distinguished by their contemporary design and impressive heating capabilities, these units cater to homeowners seeking a modern solution for efficient warmth and ambiance.

One of the primary features of the KHLDV Series is its versatile design options. Available in various sizes and styles, these fireplaces can seamlessly integrate into diverse interior décor themes. The clean face design allows for a wide viewing area of the flames, providing an unobstructed view that enhances the overall experience. The elegant finish options, ranging from sleek black to decorative trim, make it easy for consumers to customize their unit to suit their personal style.

The KHLDV Series is also noted for its advanced heating technology. Utilizing direct venting, it ensures efficient operation while minimizing heat loss. This technology allows the fireplace to draw air from outside for combustion, which not only improves energy efficiency but also maintains optimal indoor air quality by preventing the depletion of oxygen in the living area. The balanced flue design further ensures that harmful gases are vented safely outside, giving homeowners peace of mind.

Control is another significant advantage of the KHLDV Series. Equipped with a multi-function remote control system, users can easily adjust the flame height and heat output to achieve their desired ambiance and comfort levels. This intuitive control system enhances the overall user experience, allowing homeowners to create a cozy environment with minimal effort.

Safety features are also a crucial consideration in the design of the KHLDV Series. Each unit comes with a built-in safety pilot system that ensures the fireplace operates reliably and safely, providing an additional layer of security for families. The high-quality materials used in construction further enhance durability, ensuring that the fireplace can withstand the test of time.

In summary, the Monessen Hearth KHLDV Series is a perfect blend of style, efficiency, and safety. With its sleek design, advanced heating technology, user-friendly control, and robust safety features, this series transforms any living space into a warm and inviting sanctuary. Ideal for modern homes, the KHLDV Series stands out as a compelling choice for those looking to enhance their home with a functional and elegant fireplace.

Monessen Hearth KHLDV SERIES manual Remote Wall Switch Installation, Remote Wall Mounted Switch

Models: KHLDV SERIES