Monessen Hearth TPB24, TPB30, TPB18 specs

CLEARANCES and HEIGHT REQUIREMENTS

Heat resistant material (minimum requirements) with wooden mantel or other combustible projection:

To install the heater with a wooden mantel, shelf or other combustible projection above, first measure the heat resistant mate- rial shown in Figure 6, then refer to Table B.

	8" or More of
	Heat Resistan
Hood	Material
Hood
Heater in
Fireplace or
Firebox

Figure 6 - Measuring Heat Resistant Material for Mantel

HEAT RESISTANT	REQUIREMENTS FOR SAFE INSTALLATION WITH WOODEN MANTEL, SHELF
MATERIAL	OR OTHER COMBUSTIBLE PROJECTIO
MEASUREMENT	TBP18	TBP24	TBP30
12" or more	Hood not required. Observe	Hood not required. Observe	Hood not required. Observe
	proﬁles (side elevations)	proﬁle (side elevations) shown	proﬁle (side elevations) shown
	shown in Figure 7, page 14.	in Figure 9, page 15	in Figure 9, page 15
8" to less than 12"	Install hood and observe pro-	Install hood and observe pro-	Install hood and observe pro-
	ﬁles shown in Figure 8, page	ﬁles shown in Figure 7, page	ﬁles shown in Figure 7, page
	15; OR extend heat resistant	15; OR extend heat resistant	15; OR extend heat resistant
	material to at least 12" and	material to at least 12" and	material to at least 12" and
	observe proﬁles shown in	observe proﬁles shown in	observe proﬁles shown in
	Figure 7, page 14.	Figure 9, page 15.	Figure 9, page 15.
Less than 8"	Extend heat resistant mate-	Extend heat resistant mate-	Extend heat resistant mate-
	rial to at least 8", install hood	rial to at least 8", install hood	rial to at least 8", install hood
	and observe proﬁles shown in	and observe proﬁles shown in	and observe proﬁles shown in
	Figure 8, page 15; OR extend	Figure 7, page 15; OR extend	Figure 7, page 15; OR extend
	heat resistant material to at	heat resistant material to at	heat resistant material to at
	least 12" and observe proﬁles	least 12" and observe proﬁles	least 12" and observe proﬁles
	shown in Figure 8, page 14	shown in Figure 9, page 15.	shown in Figure 9, page 15.

TABLE B - Heat Resistant Material Heights and Mantel Location

70D0004

13

Image 13

Monessen Hearth TPB24, TPB30, TPB18 manual Measuring Heat Resistant Material for Mantel

Contents

What to do if YOU Smell GAS Read and Save These Instructions Contents Installer Important Safety InformationOwner Massachussetts Residents only Getting Started What YOU will Need for InstallationMake Sure YOU have Received ALL Parts Product Features and Specifications Codes General Installation InformationAdequate Combustion and Ventilation AIR BTU / Hr = Hearth Minimum Dimension Fireplace and Hearth Dimensions Height of Restriction Minimum Depth of Fireplace/Firebox Placement in a Fireplace with a Restrictive Barrier Sidewall and Ceiling Clearances Clearances and Height Requirements Clearances and Height Requirements Measuring Heat Resistant Material for Mantel Minimum Mantel Clearance with No Hood -TPB18 Mum of 10 at a minimum of 28 above the opening Minimum Clearance above Combustible Flooring Floor Clearance Before Fully Installing the Unit Installing Vented ApplicationsBefore Installing the Appliance Damper Stop Installation Assembly Procedure Installing Vented ApplicationsPlacing and Securing Appliance Flexible Tube Manual Shutoff Gas Supply Inlet Valve Connecting the GAS MILLI-VOLT Valve Control Figure Checking GAS Pressure Connecting Optional Wall Switch or Thermostat Electrical Wiring MILLI-VOLTATE Checking System Operation Connecting Remote ReceiverComplete MILLI-VOLT System Check Installing Charred Timber Logs on Burner LOG Placement Installing Left Base Log #3 Installing Left Top Log #5 Placing Rock Wool Installing Right Top Log #6 Optional Riser Installation Riser and Steel BAR Grate InstallationSteel BAR Grate Installation Cast Iron Grate Installation Optional Cast Iron Grate and Andiron InstallationAndiron Installation Placing the Decorative Rock Flame AppearanceChecking the Pilot Flame MILLI-VOLT Control and Thermostat Control Operating Instructions Checking the Burner Flame What to do if YOU Smell GAS Operating Instructions To Turn OFF GAS to Heater Cleaning and Servicing Operating Instructions and Cleaning and Servicing Observed Problem Possible Cause Remedy Troubleshooting ODS/pilot lights, but flame Burner Assembly Replacement Parts Accessories Sold Separately Replacement Parts List CTCL18 CTCL24 CTCL30 Charred Timber Logs 70D0004 Carbon Monoxide Detector Requirements Special Requirements Five Year Warranty Lifetime WarrantyBasic Warranty