Manuals / Moxa Technologies / Computer Equipment / Network Card

Moxa Technologies 5400 Connecting the Hardware, Wiring Requirements, Connecting the Power

Models: 5400

1 96

Download 96 pages 46.55 Kb

Page 11

Getting Started

Connecting the Hardware

This section describes how to connect NPort 5400 to serial devices for first time testing purposes. We cover Wiring Requirements, Connecting the Power, Grounding NPort 5400, Connecting to the Network, and Connecting to a Serial Device.

Wiring Requirements

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your NPort 5400.

Wiring Caution!

Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment.

Temperature Caution!

Please take care when handling NPort 5400. When plugged in, NPort 5420/5430/5430I’s internal components generate heat, and consequently the casing may feel hot to the touch.

You should also pay attention to the following points:

Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.

NOTE: Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.

You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.

Keep input wiring and output wiring separate.

Where necessary, it is strongly advised that you label wiring to all devices in the system.

Connecting the Power

Connect the 12-48 VDC power line with NPort 5400’s terminal block. If the power is properly supplied, the “Ready” LED will show a solid red color until the system is ready, at which time the “Ready” LED will change to a green color.

NPort 5400 Series User’s Manual 2-3

Image 11

Moxa Technologies 5400 user manual Connecting the Hardware, Wiring Requirements, Connecting the Power, Getting Started

Contents

Third Edition, May Series User’s ManualDisclaimer Copyright NoticeTrademarks Table of Contents Chapter IP Serial LIB Introduction Overview Package ChecklistProduct Features Introduction Product SpecificationsRegulatory Approvals Power RequirementsMechanical EnvironmentGetting Started Panel Layout Connecting the HardwarePanel Layout Getting Started Connecting the HardwareWiring Requirements Connecting the PowerGrounding NPort Connecting to the NetworkConnecting to a Serial Device LED IndicatorsThis chapter includes the following sections ConfigurationLCM Display Factory Default IP AddressDefault IP address Initializing NPort’s IP AddressDetailed Menu Options Initial IP Address ConfigurationButton Name Action Inact. time Delimiter Initial IP Address Configuration ARP NPort Administration SuiteTelnet Console NPort 5400 Series User’s Manual Initial IP Address Configuration Page Choosing the Proper Operation Mode TCP Server Mode Choosing the Proper Operation Mode TCP Client ModeUDP Mode Real COM ModeNPort 5400 Series User’s Manual Web Console Configuration Opening Your Browser Web Console Configuration Time zone Basic SettingsTime Server nameTime server Network SettingsSetting Factory Default Necessity ConsoleNPort 5400 Series User’s Manual Gateway IP AddressNetmask DNS server 1 / DNS sever IP ConfigurationIP Address Report Web Console Configuration Snmp SettingsPort alias Serial SettingsWeb Console Configuration Serial Parameters TCP alive check time Operating SettingsReal COM Mode Setting Factory Default Necessity To 99 min Min OptionalMax Connection 2 to Setting Factory Default Necessity To FF None OptionalMax Connection Max. ConnectionForce Transmit TCP Server ModeSetting Factory Default Necessity To 65535 ms Optional Max Connection 2 to Inactivity timeLocal TCP port Setting Factory Default Necessity 4001 RequiredCommand port Setting Factory Default Necessity 966 OptionalTCP Client Mode NPort 5400 Series User’s Manual TCP connection Destination IP addressDestination IP address 2/3/4 UDP Mode Local listen port Any host can access the NPort Accessible IP SettingsOnly one host of specific IP address can access the NPort Hosts on the specific subnet can access the NPortDCD changed Auto Warning SettingsEvent Type Trap Setting Factory Default Necessity Enable, Disable OptionalDSR changed MailSnmp Trap Server Auto warning E-mail and Snmp TrapMail Server Change Password Load Factory Default Page Configuring Windows Administrator Installing Windows Administrator Configuring Windows Administrator Configuration Broadcast Search Unlock Unlock Password ProtectionLock Lock Fixed Configuring NPort 5410/5430/5340IBlank FixedUpgrade Firmware Export/Import Add Target Select target from the list MonitorConfiguring Windows Administrator NPort 5400 Series User’s Manual Port Monitor On-line COM Mapping COM MappingConfiguring Windows Administrator Fast Flush only flush local buffer Off-line COM Mapping IP Location Configuring Windows Administrator Page IP Serial LIB How to install IP Serial Library? What is IP Serial Library?Why Use IP Serial Library? Inquiry IP Serial LIB Function GroupsExample Program IP Serial LIBPage Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout DiagramsDB9 Female to DB9 Male for NPort Cable Wiring DiagramsPinouts and Cable Wiring Ethernet Cables Serial CablesDB9 Female to DB25 Male for NPort Well Known Port Numbers TCP Socket Application ServiceUDP Socket Application Service IP MIB Icmp MIB Snmp Agent with MIB II & RS-232 like groupAddress Translation MIB System MIB Interfaces MIBWell Known Port Numbers Input Signal Table Output Signal TablePage Service Information Following services are provided Moxa Internet ServicesMoxa Product NPort Serial Number Problem Report FormService Information Product Return Procedure NPort 5400 Series User’s Manual D-5 Revision HistoryNPort 5400 Series User’s Manual Auto IP Report Protocol AP ID & Hardware ID Mapping Table Auto IP Report FormatInfo n ID List