Auto Warning Settings, Event Type | Moxa Technologies 5400 guide

Web Console Configuration

Auto Warning Settings

Event Type

Cold start

This refers to starting the system from power off (contrast this with warm start). When performing a cold start, NPort will automatically issue an Auto warning message by e-mail, or send an SNMP trap after rebooting.

Warm start

This refers to restarting the computer without turning the power off. It’s the opposite of cold start. When performing a warm start, NPort will automatically send an e-mail, or send an SNMP trap after rebooting.

Authentication failure

The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, NPort will immediately send an e-mail or send an SNMP trap.

IP address changed

The user has changed NPort’s IP address. When the IP address changes, NPort will send an e-mail with the new IP address before NPort reboots. If the NPort fails to send mail to the mail server after 15 seconds, NPort will be rebooting directly and abort the mail auto warning.

Password changed

The user has changed NPort’s password. When the password changes, NPort will send an e-mail with the password change notice before NPort reboots. If the NPort fails to send mail to the mail server after 15 seconds, NPort will be rebooting directly and abort the mail auto warning.

DCD changed

The DCD (Data Carrier Detect) signal has changed, also indicating that the modem connection status has changed. For example, a DCD change to high also means “Connected” between local modem and remote modem. If the DCD signal changes to low, it also means that the connection line is down.

When the DCD changes, NPort will immediately send an e-mail or send an SNMP trap.

NPort 5400 Series User’s Manual 5-23

Image 49

Moxa Technologies 5400 user manual Auto Warning Settings, Event Type, DCD changed

Contents

Third Edition, May Series User’s Manual Trademarks Copyright NoticeDisclaimer Table of Contents Chapter IP Serial LIB Introduction Product Features Package ChecklistOverview Introduction Product Specifications Mechanical Power RequirementsEnvironment Regulatory Approvals Getting Started Panel Layout Connecting the Hardware Panel Layout Wiring Requirements Connecting the HardwareConnecting the Power Getting Started Connecting to a Serial Device Connecting to the NetworkLED Indicators Grounding NPort This chapter includes the following sections Configuration Default IP address Factory Default IP AddressInitializing NPort’s IP Address LCM Display Button Name Action Initial IP Address ConfigurationDetailed Menu Options Inact. time Delimiter Initial IP Address Configuration ARP NPort Administration Suite Telnet Console NPort 5400 Series User’s Manual Initial IP Address Configuration Page Choosing the Proper Operation Mode TCP Server Mode UDP Mode TCP Client ModeReal COM Mode Choosing the Proper Operation Mode NPort 5400 Series User’s Manual Web Console Configuration Opening Your Browser Web Console Configuration Time Basic SettingsServer name Time zone Setting Factory Default Necessity Network SettingsConsole Time server NPort 5400 Series User’s Manual Netmask IP AddressGateway DNS server 1 / DNS sever IP Configuration IP Address Report Web Console Configuration Snmp Settings Port alias Serial Settings Web Console Configuration Serial Parameters Real COM Mode Operating SettingsSetting Factory Default Necessity To 99 min Min Optional TCP alive check time Max Connection Setting Factory Default Necessity To FF None OptionalMax. Connection Max Connection 2 to Setting Factory Default Necessity To 65535 ms Optional TCP Server ModeForce Transmit Max Connection 2 to Inactivity time Command port Setting Factory Default Necessity 4001 RequiredSetting Factory Default Necessity 966 Optional Local TCP port TCP Client Mode NPort 5400 Series User’s Manual Destination IP address 2/3/4 Destination IP addressTCP connection UDP Mode Local listen port Only one host of specific IP address can access the NPort Accessible IP SettingsHosts on the specific subnet can access the NPort Any host can access the NPort Event Type Auto Warning SettingsDCD changed DSR changed Setting Factory Default Necessity Enable, Disable OptionalMail Trap Mail Server Auto warning E-mail and Snmp TrapSnmp Trap Server Change Password Load Factory Default Page Configuring Windows Administrator Installing Windows Administrator Configuring Windows Administrator Configuration Broadcast Search Lock Unlock Password ProtectionUnlock Blank Configuring NPort 5410/5430/5340IFixed Lock Fixed Upgrade Firmware Export/Import Add Target Select target from the list Monitor Configuring Windows Administrator NPort 5400 Series User’s Manual Port Monitor On-line COM Mapping COM Mapping Configuring Windows Administrator Fast Flush only flush local buffer Off-line COM Mapping IP Location Configuring Windows Administrator Page IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library? Example Program IP Serial LIB Function GroupsIP Serial LIB InquiryPage Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout Diagrams Pinouts and Cable Wiring Cable Wiring DiagramsEthernet Cables Serial Cables DB9 Female to DB9 Male for NPort DB9 Female to DB25 Male for NPort Well Known Port Numbers TCP Socket Application Service UDP Socket Application Service IP MIB Icmp MIB Snmp Agent with MIB II & RS-232 like group Address Translation MIB System MIB Interfaces MIB Well Known Port Numbers Input Signal Table Output Signal TablePage Service Information Following services are provided Moxa Internet Services Service Information Problem Report FormMoxa Product NPort Serial Number Product Return Procedure NPort 5400 Series User’s Manual D-5 Revision History NPort 5400 Series User’s Manual Auto IP Report Protocol Info n Auto IP Report FormatID List AP ID & Hardware ID Mapping Table