Manuals / Multi-Tech Systems / Computer Equipment / Modem

Multi-Tech Systems MT5634ZPX-PCI-V92 Data Terminal Ready DTR Control, XON/XOFF Pacing Control

Models: MT5634ZPX-PCI-V92

1 85

Download 85 pages 32.44 Kb

Page 32

MultiModemZPX User Guide		4 AT Commands, S-Registers, and Result Codes
Command:	&Dn	Data Terminal Ready (DTR) Control
Values:		n = 0, 1, 2, or 3
Default:		2
Description:	&D0	Modem ignores the true status of the DTR signal and responds
		as if it is always on.
	&D1	If DTR drops while in online data mode, the modem enters
		command mode, issues an OK, and remains connected.
	&D2	If DTR drops while in online data mode, the modem hangs up.
		If the signal is not present, the modem will not answer or dial.
	&D3	If DTR drops, the modem hangs up and resets as if an ATZ
		command were issued.
Command:	&En	XON/XOFF Pacing Control
Values:		n = 12 or 13
Default:		12
Description:	&E12	Disables XON/XOFF pacing.
	&E13	Enables XON/XOFF pacing. (&K4 must also be set.)

Note: &E13 has no effect if hardware control (&K3) is selected.

Command:	&Fn	Load Factory Settings
Values:		n = 0
Default:		None
Description:	&F0	Loads factory settings as active configuration.
Note: See also the Z command.

Command:	&Gn	V.22bis Guard Tone Control
Values:		n = 0, 1, or 2
Default:		0
Description:	&G0	Disables guard tone.
	&G1	Sets guard tone to 550 Hz.
	&G2	Sets guard tone to 1800 Hz.
Note: The &G command is not used in North America.

Command:	&Kn	Flow Control Selection
Values:		n = 0, 3, or 4
Defaults:		3
Description:	&K0	Disables flow control.
	&K3	Enables CTS/RTS hardware flow control.
	&K4	Enables XON/XOFF software flow control.

Command:	&Qn	Asynchronous Communications Mode
Values:		n = 0, 5, 6, 8, or 9
Default:		5
Description:	&Q0	Asynchronous with data buffering. Same as \N0.
	&Q5	Error control with data buffering. Same as \N3.
	&Q6	Asynchronous with data buffering. Same as \N0.
	&Q8	MNP error control mode. If MNP error control is not estab-
		lished, the modem falls back according to the setting in S36.
	&Q9	V.42 or MNP error control mode. If neither error control is es-
		tablished, the modem falls back according to the setting in S36.

27

Image 32

Multi-Tech Systems MT5634ZPX-PCI-V92 manual Data Terminal Ready DTR Control, XON/XOFF Pacing Control, Load Factory Settings

Contents

Page Record of Revisions Introduction Solving Problems Appendix G Installing Under SCO OpenServer Introduction Product Description What Is in Your Modem Package?Introduction Installation Safety Warnings What You Will NeedWe supply You supplyInstall the MultiModemZPX in your Computer Phone Connection Make the External ConnectionsLine Connection Microphone Connection Sound Card and Speaker ConnectionsWindows 98/Me Install the Modem DriverWindows Changing the Windows 95/98/Me COM port assignment Verifying the Windows 95/98/Me Configuration If Dial-Up Networking is not installed Windows NTIf Dial-Up Networking is already installed Verifying the Windows NT Configuration Viewing system resources Global Wizard Utility Configure the Modem for Your CountryAT Commands Install and Configure Your Software Operation Connecting to the Internet Configuring the ModemPhoneTools Features Dial-Up Networking Sending a FaxReferences AT Commands Registers Result Codes Introduction AT Commands Repeat Last CommandCommunication Standard Setting AnswerEcho Command Mode Characters DS=n Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Modulation HandshakeModem Reset Tone DialingResult Code Format Result Code OptionsLoad Factory Settings Asynchronous Communications ModeData Terminal Ready DTR Control XON/XOFF Pacing ControlTest Commands Display Current SettingsStore Current Configuration Store Dialing Command\Kn Break Control \Bn Transmit Break\Jn Data Buffer Control \Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \V n Protocol Result CodeAdaptive Answer Result Code Enable Data Calling ToneView Numbers in Blacklist 42bis Compression ControlData Compression Reporting Command +DCS=x,y Select V.44 Data CompressionCommand +DS44=n V.44 Data Compression Enable Synchronous Buffered Mode SubparametersModulation Selection ModCommand +PCW= n Call Waiting Enable Modem on Hold Enable Command +PMHR=n Modem on Hold InitiatePCM Upstream Ignore Modem Hook FlashCommand +PMHT=n Modem on Hold Timer Quick Connect ControlCommand +VCID=n Caller ID Selection Command +VDR=x, y Distinctive Ring Report#Sx Enter Setup Password #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCR Remote Configuration Escape SequenceRegister Unit Range Default Description RegistersValue Speed Value RateBit 56K mode Value Digital lossResult Codes Terse Verbose DescriptionDelayed Remote Configuration To Change the Setup Password Basic ProcedureSetup To Change the Remote Escape Character Solving Problems Modem Does Not Respond to Commands Modem Cannot Connect When Dialing ModemDisconnects While Online MultiModemZPX User Guide There Are Garbage Characters on the Monitor Modem Doesn’t Work with Caller IDFax and DataSoftware Can’t Run at the Same Time Voice Functions Don’t WorkSpeakerphone Test Voice Mail TestLoopback Test Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFCC Part Fax Branding StatementProtection Against Contact with TNV Circuit Canadian Limitations NoticeIndustry Canada EMC, Safety, and R&TTE Directive Compliance New Zealand Telecom Warning NoticeSouth African Notice International Modem RestrictionsAppendix B Technical Specifications Command Buffer Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMultiModemZPX User Guide Loopback Tests Canadian Customers Limited WarrantyOnline Warranty Registration Service International Customers outside U.S.A. and Canada International DistributorsTechnical Support Internet SitesUpgrade Overview Identify the Modem FirmwareDownload the Upgrade File Extract the Upgrade FilesIdentify the Current Firmware Version Document and Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersPC port Linux port InstallationStandard Linux Serial Port Definitions Using the Terminal Program Minicom to Verify Operation Using the Modem to Call the InternetCalling the ISP Answering CallsAppendix G Installing Under SCO OpenServer Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index