Fuel and chemical exposure Warnings | Multiquip EHTX44Y5 specification

fuel and chemical exposure Warnings

Diesel engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals know to cause cancer, birth defects and other reproductive harm.

Some examples of these chemicals are:

Lead from lead-based paints

Crystalline silica from bricks

Cement and other masonry products

Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: ALWAYS work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

page 2 — eHtx44y RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13)

Image 2

Multiquip EHTX44Y5 operation manual Fuel and chemical exposure Warnings

Contents

Model eHTX44Y5 Fuel and chemical exposure Warnings Silicosis Warning Respiratory Hazards Ehtx Ride-On Trowel Page Training checklist Completely Daily pre-operation checklist Burn hazards SaFeTy meSSageSExplosive fuel hazards Rotating parts hazards GeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipment „ Use well-insulated gloves when picking up the battery FueL SaFeTyBaTTeRy SaFeTy „ aLWayS shutdown engine before transporting TRaNSpORTINg SaFeTy„ NeveR lift trowel with the operator on the machine Emission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire life DIMENSIONS/SPECIFICATIONS Ehtx Guaranteed ISO 37442010 Based SpecificationsGuaranteed ISO 112012010 Based Sound Power Level in dBA b General Information Controls and Indicators Hour Meter Indicates number of hours machine has been used 25 20 Engine Components Fuel Filter Removes dirt and water from the engine fuel Seat assembly SetupTrowel Setup Instructions Battery Setup Engine Oil Level InspectionHydrauic Oil Level Fuel Place the engine speed control lever, in the LOW position Insert the ignition key into the ignition switch, FigureOperation Steering Place the engine speed control lever, in the High position Trowel Speed Limiter Control Blade Pitch Control Clean and remove any foreign debris from the trowe Engine Shut-Down MAINTENANCE OFF position Air CleanerRemove the air cleaner element Filter element from the inside out Checking Engine Oil DailyChanging Engine Oil And Filter Vol % Freezing Point Boiling Point Anti Operation in Freezing WeatherGal 9.5 liters 108 226 Fuel/Water Separator Radiator MaintenanceFuel Filter Oil And Fuel Lines Battery/Charging SystemCheck and clean battery terminals for corrosion Checking The V-Belt Left Side Trowel Speed Adjustment Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Engine Tune-Up Blade Pitch Adjustment Procedure Blade Pitch Adjustment Bolt Stabilizer Ring Removal Changing Blades Place the trowel on a FLAT, Level surface Trowel Arm AdjustmentSpider Removal Remove the trowel arm from the spider plate Trowel Arm RemovalRemove spider to hydraulic motor retainingscrew Locate the trowel arm adjustment tool P/N Checking Trowel Arm Straightness Re-Assembly Trowel Arm Adjustment Fixture Components Lifting/Crush Hazard. do not lift trowel with pans attached Installing Pans Onto Finisher BladesChecking Hydraulic Steering Pressure Hydraulic Pump Pressure Test Ports Cool Oil1 155-175 PSI Hot Oil 145-165 PSI Steering Pressure AdjustmentChecking Steering Pressure Pitch Pressure Check Pitch Pressure Out of SpecificationPress the left pitch rocker switch downward Pitch Pressure Adjustment Pitch Pressure Adjustment Wiring Diagram SWITCH,KEY Hydraulic Diagram Troubleshooting Troubleshooting Ride-On Hydraulic Trowel Wiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help