SETUP

NOTICE

The pole clamp assembly used in this setup procedure is a dual type clamp. One side of the clamp is for the attachment of the main pole of the lighting system.The other side of the clamp is used for the attachment of a support pole that is usually connected to a piece of equipment such as a paver.

POLE SETUP

Refer to Figure 6 for the following procedure.

1.Remove the offset pole (B) from the shipping container.

2.Attached to the offset pole is a 17/19 mm open-end wrench (C). Remove the wingnut (D) securing the wrench to the offset pole and remove wrench.

3.Reinsert wingnut and washer back into offset pole so they will not get lost or misplaced.

4.Remove the two pole clamp assemblies (A) from the shipping container. Attach one pole clamp assembly

(E) to the main pole (F) about 3 inches (76.2 mm) down from the main pole extension clamp. Using supplied 19 mm wrench, tighten locknut on the pole clamp assembly securely.

5.Attach the other pole clamp assembly (G) to the main pole (F) about 7.0 in. (140 mm.) down from the previous attached pole clamp assembly (E). Using the 19 mm wrench, tighten locknut on the pole clamp assembly securely.

6.To attach main pole (F) to equipment support pole (I), swing open adjustable tension plate (H) on clamp so that it can accomodate the diameter of the equipment support pole. Insert equipment support pole (I) through the two equipment support pole clamp assemblies as shown in Figure 6.

7.Once the equipment support pole (I) has been seated properly, move adjustment bolt and locknut (J) into locking position. Use the supplied 17 mm wrench, to tighten locknuts (J) on both clamps securely.

8.Place offset pole (B) with adapter clamp (K) on top of adjustable extension pole (L). Make sure that offset pole has been seated correctly.

9.Using 17 mm wrench, tighten both bolts (M) on the offset adapter clamp (K) securely.

10.Place lamp assembly (N) onto offset pole (B). Tighten T-handle bolt (O) securely.

 

 

 

N

 

 

 

 

 

 

LAMP

 

 

 

 

 

 

ASSEMBLY

 

 

 

 

 

 

 

B

 

 

 

 

 

 

OFFSET

 

 

 

 

 

 

POLE

 

 

 

 

 

O

 

K

 

 

T-HANDLE

OFFSET

P

 

 

 

ADAPTER

 

 

 

CLAMP

BALLOON

 

 

C

 

 

 

 

 

POWER

 

 

M

 

 

 

 

 

 

 

CABLE

 

 

 

 

 

 

 

REMOVE

 

L

 

 

 

WRENCH

WINGNUT

ADJUSTABLE

 

 

 

 

 

 

D

EXTENSION

 

 

 

POLE

 

 

 

 

 

 

 

 

EQUIPMENT

J

 

EXTENSION

ADJUSTMENT

 

CLAMP

Q

SUPPORT

 

 

BOLT

 

 

BOLT AND

 

 

POLE CLAMP

 

 

 

 

 

 

 

LOCKNUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.0 IN.

LOCKNUT

 

 

 

(76.2 MM

 

 

 

 

 

 

 

 

 

E

 

 

 

MAIN POLE

 

H

POLE

 

 

 

CLAMP

 

 

 

 

 

TENSION

CLAMP

 

 

 

ADJUSTABLE

ASSY.

 

 

 

 

PLATE

 

 

 

CHANNEL

 

 

 

 

 

 

 

 

 

MAIN

 

 

 

 

 

 

POLE

 

 

7.0 IN.

 

 

 

F

 

 

 

 

 

(140 MM

POLE

 

 

 

 

 

 

CLAMP

 

 

G

 

 

 

ASSEMBLY

 

 

 

 

 

A

 

 

POLE

 

 

 

 

 

CLAMP

 

 

 

 

 

 

 

 

 

 

 

 

ASSY.

 

 

 

EQUIPMENT

SUPPORT

POLE

I

Figure 6. Offset Pole Assembly

PAGE 16 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09)

Page 16
Image 16
Multiquip GB114BS/BP manual Pole Setup