INFLATING BALLOON AND TURNING ON LAMPS (MLT ONLY)
1.On MLT series light towers, reconnect the
MLT LIGHT TOWER
WHISPERWATT |
|
|
|
|
|
| |||
7KW AC |
|
|
|
|
|
|
|
| |
Model |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| ON |
|
|
|
|
|
|
|
|
|
| STOP | RUN | |
|
|
|
|
|
| OFF |
| HEAT | |
| AC CIRCUIT | AC | VOLTMETER | IDLE CONTROL |
|
|
| ||
|
|
|
|
|
|
| |||
7000 | BREAKER |
|
|
| 00000 |
|
| START | |
WATT |
|
|
|
|
|
| |||
|
|
|
| HOURS |
|
|
| ||
DIESEL |
|
|
|
|
| STARTER |
| ||
| POWERED AC G | ENERATOR |
| HOUR | METER | SWITCH | |||
|
|
|
|
|
| ||||
20A |
|
|
|
|
|
|
|
|
|
| 25A |
|
|
|
|
|
|
|
|
120V |
|
| 25A |
|
|
|
| ||
|
|
|
|
|
| 25A |
|
| |
|
|
|
|
| 120/240V |
|
|
| |
TO BALLAST
Figure 13. MLT Ballast 4-pin
Power Cable
2.Slightly raise the light tower mast to allow clearance for the balloon to inflate.
3.Start the light tower engine as referenced in the MLT operation manual.
4.Once, the engine has started, place the main circuit breaker switch (Figure 14) on the MLT front control panel in the ON position.
MLT LIGHT TOWER
OPERATION
5.Next, turn on lamp circuit breakers The balloon should begin to inflate and the lamps will light.
6.Secure any unused lamp cables.
7.Raise the light tower mast to the desired upright height.
DEFLATING AND STORING BALLOON
1.Turn lamps OFF and allow to cool for at least five minutes.
2.Once the lamps have cooled, place the main breaker switch in the OFF position.
NOTICE
ALWAYS make sure lamps are turned off and allowed
to cool before deflating balloon to avoid any damage to the balloon. NEVER transport GB4000 lamp fixture while attached to mast.
3.When the balloon is completely deflated, unzip the protective cover and fold the balloon inside the cover.
4.Carefully zip up the cover and snap the buttons to fully close the protective cover.
5.Remove all cables from
6.Pull cotter pin from locking pin and remove lamp assembly from light tower mast.
7.Store lamp assembly in a safe place where it will not get damaged.
MAIN CIRCUIT
BREAKER
(ON)
WHISPERWATT |
|
|
|
|
|
| |||
7KW AC |
|
|
|
|
|
|
|
| |
Model |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| ON |
|
|
|
|
|
|
|
|
|
| STOP | RUN | |
|
|
|
|
|
| OFF |
|
| HEAT |
|
| AC | VOLTMETER | IDLE | CONTROL |
|
|
| |
|
|
|
|
|
| ||||
| AC CIRCUIT |
|
|
|
|
|
|
|
|
7000 | BREAKER |
|
|
| 00000 |
|
| START | |
WATT |
|
|
|
|
|
| |||
|
|
|
| HOURS |
|
|
| ||
DIESEL |
|
|
|
|
| STARTER |
| ||
| POWERED AC G | ENERATOR |
| HOUR | METER | SWITCH | |||
20A |
|
|
|
|
|
|
|
|
|
| 25A |
|
|
|
|
|
|
|
|
120V |
|
| 25A |
|
|
|
| ||
|
|
|
| 25A |
|
| |||
|
|
|
|
| 120/240V |
|
|
| |
TO BALLAST
Figure 14. Main, GFCI Circuit Breakers (ON/MLT)
GB4000 BALLOON LIGHT• OPERATION AND PARTS MANUAL — REV. #1 (02/25/14) — PAGE 25
