NAD C 525BEE owner manual Skip, Stand-Byindicator, Power On, Power Off, Numeric Keypad, Program

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO PORTUGUÊS SVENSKA

11. SKIP
During playback, press the SKIP	button once to skip back to the
beginning of the current track. Press SKIP		twice in rapid succession

to skip back to the previous track or previous programmed track in Program Play mode, once to reach the beginning of the current track and again to jump to the previous track. When pressing continuously, the player will skip to previous tracks repeatedly, concluding at the beginning of the disc (Track 1) or the first track programmed in Program Play mode.

During playback, press the SKIP once to skip to the beginning of the next track on the disc or next programmed track in Program Play mode. Thus, to sample each song, press PLAY and then tap SKIP after you’ve heard a few seconds of each track. From Stop, press the SKIP button until you’ve reached the track from where you want to

start playback. Press Play to start playback.

12. STAND-BY INDICATOR

The stand-by indicator turns on in green when the unit is switched on, and changes to amber when switched to stand-by mode.

REMOTE CONTROL

A wireless remote control is provided with your compact disc player, enabling you to operate play-back functions from the comfort of your chair or from virtually anywhere in the room. For reliable operation there should be a clear line-of-sight path from the remote control to the front of the CD player. If the player does not respond to remote commands, it may be that this line-of-sight path is obstructed by clothing, paper, or furnishings.

Most of the buttons on the remote control handset have the same effect as the corresponding buttons on the front panel of the disc player. In addition the handset is equipped with some extra buttons and functions, such as the numeric keypad and Program functions.

POWER ON

Press the Green button to swith on the power to the disc player from stand-by mode. The LED will change from amber to green, and the display will illuminate.

POWER OFF

Press this red button to switch to stand-by mode from power on mode. The LED will change from green to amber and the display will go dark.

NUMERIC KEYPAD

Using the direct-entry numeric keypad (1 to 10; +10) causes the player to jump directly to the beginning of a numbered track and commence play. Thus to play Track 5, simply press 5. To play Track 20, press: +10, 10. To play Track 36, press: +10, +10, +10, 6.

PROGRAM

The C 525BEE CD player allows for programmed playback of up to 20 tracks in any desired order. To engage Program Play with your desired track sequence in the memory:

1Press PROGRAM. The “MEMORY” indicator will light up. The display indicates “Pr p:01”, meaning that the player is awaiting the first Program entry.

2Use the SKIP or the Direct-Entry Numeric keypad buttons to select the first track in your planned sequence. The selected track number will blink in the display.

3Press PROGRAM to store the selected track number in memory. The display will revert to show Program-Entry mode and advance to “Pr p:02”, showing that the player is ready for your second entry.

4Repeat Steps 2 and 3 to select and store other track numbers in memory, up to a maximum of 20 entries. The display will show “FULL” when 20 tracks have been entered.

5If you want to review or edit your program entries, press PROGRAM repeatedly to cycle the display through them. When the highest program number is displayed, you can enter additional tracks in the memory by repeating Steps 2 and 3.

6To play the stored program, press PLAY. “MEMORY” will appear in the display, indicating that a stored program is being played. During Program Play the SKIP buttons will access only the tracks in the program list. So if you want to play only a portion of a stored

program, initiate play and press SKIP to jump over the programmed tracks that you don’t want to hear.

7To terminate program play, press STOP. However the stored track list remains in memory; if you want to play the program again, simply press PLAY again. If you want to edit the program, press PROGRAM repeatedly to review the list and change. To add tracks, press the PROGRAM button until the highest program number is displayed.

8To clear the program memory, press STOP, OPEN/CLOSE to open the drawer, or switch off the POWER.

The following example presents a step-by-step illustration of how to program and start Program Play to play tracks 5, 23, 9, 16, and 1.

While the CD player is stopped:
Press on remote control	Display shows
PROGRAM	Pr	p:01
5	5	p:01
PROGRAM	Pr	p:02
+10, +10, 3	23	p:02
PROGRAM	Pr	p:03
9	9	p:03
PROGRAM	Pr	p:04
+10, 6	16	p:04
PROGRAM	Pr	p:05
1	1	p:05
PROGRAM	Pr	p:06
PLAY

6