NAD T175 owner manual Using the Htrc 1 Remote Control, Getting Familiar with the Htrc, Highlights

ENGLISH

FRANÇAIS

ESPAÑOL

ITALIANO

DEUTSCH NEDERLANDS SVENSKA

РУССКИЙ

OPERATION

USING THE HTRC 1 REMOTE CONTROL

IDENTIFICATION OF CONTROLS

•Top section features ON/OFF buttons and back-light LCD display.

• Upper section has eight DEVICE SELECTOR keys including one programmable CUSTOM DEVICE SELECTOR key and an additional MACRO button function key.

• The upper middle section with channel, volume, MUTE, and surround mode buttons.

• Middle section has DVD, CD, TUNER and OSD navigation buttons.

•Lower middle section has number buttons 0 to 9, A/V PSET, SPEAKER and CD functions, DVD

SETUP, and tuner-preamplifier’s TEST and DELAY buttons.

• Lower section has DVD and CD transport buttons, tuner-preamplifier audio function keys as well as DVD resolution button.

• Bottom section with CHANNEL VOLUME trimming buttons.

INTRODUCTION

The HTRC 1 is like having eight virtual remote controls in one. The eight DEVICE SELECTOR keys can be used to switch between the different virtual remote controls or devices.

When the HTRC 1 is idle, the name of the currently selected device will be shown on the first line of the LCD display. Whenever a function key is pressed, the name of that function will be shown on the second line of the LCD display. The second line will be cleared again shortly after releasing the function key.

HIGHLIGHTS

•Controls up to 8 Devices.

•2-line LCD display indicates selected Device (DVD) and sent Command (PLAY) (for example).

• Preprogrammed with all NAD remote commands including Zone 2.

• Learning function - learns up to 360 commands from other remotes.

•Macro operations - program up to 52 Macros with as many as 64 commands each to automate

commonly used command sequences.

•Punch Though Operations permit easy access to commonly used functions without reselecting a

device.

• Full illumination with light sensor and adjustable time out for easy operation in low light conditions.

• Can generate IR signals with a carrier frequency up to 500 kHz (B&O® compatible).

•Mini USB PC Interface allows programming from a Personal Computer.

The HTRC 1 is already preprogrammed with a full complement of NAD commands on its AMP DEVICE SELECTOR page, and with library commands to operate most NAD DVD, CD and TUNER components on the corresponding DEVICE SELECTOR keys. These default commands are permanent: Even if you teach the HTRC 1 new commands to take their place, the underlying library commands remain in place and can easily be recalled should you add an NAD component to your system later.

GETTING FAMILIAR WITH THE HTRC 1

The HTRC 1 is divided into three main sections. The LCD display section at the top of the handset, the

DEVICE SELECTOR, and the remaining 44 Control keys.

Eight DEVICE SELECTOR keys at the top; AMP, TV, CUSTOM, CD, DVD, VCR, TUNER, and CABLE/SAT determine which component the remaining 44 control keys will operate. A DEVICE SELECTOR key determines what component the HTRC 1 will command; with factory defaults, it does not perform any function on the T 175. The DEVICE SELECTOR keys are organized into three vertical rows of 3 buttons each; the row on the left are all Audio devices, the row in the center are all Video devices.

Both the DEVICE SELECTOR and function keys can “learn” control codes from virtually any infrared remote controller, allowing you to teach the codes of your equipment, regardless of brand, to the HTRC 1. All of the function keys on the AMP DEVICE SELECTOR are preprogrammed to control NAD amplifiers, preamplifiers, and receivers. (The HTRC 1 can also command many other NAD components, from its DVD, CD, TUNER and TV pages.)

Since HTRC 1 Control keys can perform different functions, depending on the selected DEVICE SELECTOR key, the HTRC 1 uses color coding to indicate the function of the function keys when different device keys are chosen. Thus, the colour of the DEVICE SELECTOR key-labeling corresponds to the labeling of the function keys (similar to a calculator).

36