National Instruments IMAQ Vision for LabWindows TM /CVI P

Glossary

© National Instruments Corporation G-13 IMAQ Vision for LabWindows/CVI User Manual

offset The coordinate position in an image where you want to place the origin

ofanothe r image. Setting an offset is useful when performing mask

operations.

opening An erosion followed by a dilation. An opening removes small objects and

smooths boundaries of objects in the image.

operators Allow masking, combination, and comparison of images. You can use

arithmetic and logic operators in IMAQVision.

optical representation Contains the low-frequency information at the center and the

high-frequency information at the corners of an FFT-transformed image.

outer gradient Finds the outer boundary of objects.

P

palette The gradation of colors used to display an image on screen, usually defined

by a CLUT.

particle A connected region or grouping of non-zero pixels in a bi nary image.

particle analysis A series of processing operations and analysis functions that produce some

information about the particles in an image.

pattern matching The technique used to locate quickly a grayscale template within a

grayscale image

picture element An element of a digital image. Also called pixel.

pixel Picture element. The smallest division that makes up the video scan line.

For display on a computer monitor, a pixel’s optimum dimension is square

(aspect ratio of 1:1, or the width equal to the height).

pixel aspect ratio The ratio between the physical horizontal size and the vertical size of the

region covered by the pixel. An acquired pixel should optimally be square,

thus the optimal value is 1.0, but typically it falls between 0.95 and 1.05,

depending on camera quality.

pixel calibration Directly calibrates the physical dimensions of a pixel in an image.

pixel depth The number of bits used to represent the gray level of a pixel.

Contents

Main IMAQ Page Important Information Warranty Copyright Trademarks Patents Contents About This Manual Chapter 1 Introduction to IMAQ Vision Chapter 2 Getting Measurement-Ready Images Chapter 3 Making Grayscale and Color Measurements Chapter 4 Performing Particle Analysis Chapter 5 Performing Machine Vision Tasks Chapter 6 Calibrating Images Page About This Manual Conventions Related Documentation IMAQ Vision NI Vision Assistant NI Vision Builder for Automated Inspection Other Documentation Introduction to IMAQ Vision About IMAQ Vision Application Development Environments IMAQ Vision Function Tree IMAQ Machine Vision Function Tree Creating IMAQ Vision Applications Chapter 1 Introduction to IMAQ Vision National Instruments Corporation 1-5 IMAQ Vision for LabWindows/CVI User Manual Chapter 1 Introduction to IMAQ Vision IMAQ Vision for LabWindows/CVI User Manual 1-6 ni.com Getting Measurement-Ready Images Set Up Your Imaging System Calibrate Your Imaging System Create an Image Page Source and Destination Images Acquire or Read an Image Acquiring an Image Reading a File Converting an Array to an Image Display an Image Attach Calibration Information Analyze an Image Improve an Image Lookup Tables Filters Convolution Filter Nth Order Filter Grayscale Morphology FFT Complex Image Operations Making Grayscale and Color Measurements Define Regions of Interest Defining Regions Interactively Page Page Page Tools Palette Transformation Defining Regions Programmatically Defining Regions with Masks Measure Grayscale Statistics Measure Color Statistics Figure 3-4. Primary Components of a 32-Bit Color Image Figure 3-5. Primary Components of a 64-Bit Color Image Note You can also use imaqExtractColorPlanes() to process the red, green, and blue components of a 64-bit image. Comparing Colors Learning Color Information Specifying the Color Information to Learn Using the Entire Image Using a Region in the Image Using Multiple Regions in the Image Choosing a Color Representation Sensitivity Ignoring Learned Colors Performing Particle Analysis Create a Binary Image Improve the Binary Image Removing Unwanted Particles Separating Touching Particles Improving Particle Shapes Make Particle Measurements Page Page Page Page Page Page Performing Machine Vision Tas ks Locate Objects to Inspect Page Using Edge Detection to Build a Coordinate Transform Page Using Pattern Matching to Build a Coordinate Transform Chapter 5 Performing Machine Vision Tasks National Instruments Corporation 5-7 IMAQ Vision for LabWindows/CVI User Manual Choosing a Method to Build the Coordinate Transform Figure 5-4. Building a Coordinate Transform Set Search Areas Defining Regions Interactively Defining Regions Programmatically Find Measurement Points Finding Features Using Edge Detection Finding Lines or Circles Finding Edge Points Along One Search Contour Finding Edge Points Along Multiple Search Contours Finding Points Using Pattern Matching Defining and Creating Good Template Images Symmetry Feature Detail Positional Information Background Information Training the Pattern Matching Algorithm Defining a Search Area Setting Matching Parameters and Tolerances Match Mode Minimum Contrast Rotation Angle Ranges Testing the Search Algorithm on Test Images Using a Ranking Method to Verify Results Finding Points Using Color Pattern Matching Defining and Creating Good Color Template Images Color Information Symmetry Feature Detail Positional Information Training the Color Pattern Matching Algorithm Defining a Search Area Setting Matching Parameters and Tolerances Color Sensitivity Search Strategy Color Score Weight Minimum Contrast Rotation Angle Ranges Testing the Search Algorithm on Test Images Finding Points Using Color Location Convert Pixel Coordinates to Real-World Coordinates Make Measurements Distance Measurements Analytic Geometry Measurements Instrument Reader Measurements Identify Parts Under Inspection Classifying Samples Reading Characters Reading Barcodes Reading 1D Barcodes Reading Data Matrix Barcodes Reading PDF417 Barcodes Display Results Page Page Calibrating Images Perspective and Nonlinear Distortion Calibration Defining a Calibration Template Defining a Reference Coordinate System Page Learning Calibration Information Specifying Scaling Factors Choosing a Region of Interest Choosing a Learning Algorithm Using the Learning Score Learning the Error Map Learning the Correction Table Setting the Scaling Method Calibration Invalidation Simple Calibration Save Calibration Information Attach Calibration Information A Technical Support and Professional Services Glossary Numbers A B Page C D E F G H I Page J K L Page M N O P Q R S T V Index Numerics A B C D E F G H I K L M N O P R S T U V W