National Instruments NI 9144 NI 9217 Calibration Data

© National Instruments Corporation 37 NI 9144 User Guide and Specifications

one conversion in the future, at time t+1. The conversion code is listed in

Table 2 9.

Note The conversion rate for every channel must match the value of the conversion speed

control in 0x2002.

For example, the scan list entry 0x00000001FC indicates this scan stores at

address 1, and the next conversion is channel 2 at high-accuracy.

Table30 contains the default scan list.

NI 9217 Calibration Data

The NI 9217 has four RTD channels that can measure 100 Ω RTD in 3-wire

and 4-wire mode. There is a 1 mA excitation current source per channel and

the module range is –500 Ω to 500 Ω. The resistance range specified in the

manual is 0 to 400 Ω. This range is tested and covers the temperature range

of –200 ºC to 850 ºC for the standard platinum RTD. The channel does not

read negative resistance.

Each channel has an associated LSB weight, which is the number of

Ωperbit, and an offset, which is the number of Ω per bit measured when

the inputs are grounded.

Table 29. NI 9217 Conversion Code

Bits Field

7:3 Conversion rate: 0b11111 = 31,

High-Accuracy

0b00010 = 2, High-Speed

2:1 Channel number

0Reserved

Table 30. NI 9217 Scan List Format

Index Sub Type Val ue

0x2001 0 ARR:U32 5

1 4

20x0000 | 0xF8 | 0x02

30x0100 | 0xF8 | 0x04

40x0200 | 0xF8 | 0x06

50x0300 | 0xF8 | 0x00

Contents

Main USER GUIDE AND SPECIFICATIONS NI 9144 Deterministic Ethernet Expansion Chassis for C Series Modules Contents Introduction Safety Guidelines Safety Guidelines for Hazardous Locations Special Conditions for Hazardous Locations Use in Europe Special Conditions for Marine Applications Mounting the NI 9144 Chassis Figure 2. NI 9144 Chassis, Bottom View with Dimensions Figure 3. NI 9144 Chassis, Front View with Dimensions Mounting the NI 9144 Chassis on a Panel National Instruments Corporation 7 NI 9144 User Guide and Specifications Figure 5. Installing the Panel Mount Accessory on the NI 9144 Chassis Figure 6. Dimensions of NI 9144 Chassis with Panel Mount Accessory Installed Caution Remove any C Series I/O modules from the chassis before removing it from the panel. Mounting the Chassis on a DIN Rail Connecting the NI 9144 Chassis to a Network Understanding LED Indications POWER LED FPGA LEDOpen FPGA Mode Only RUN and ERR LEDs INIT PRE-OP SAFE-OP Resetting the NI 9144 Network Configuration Safe-State Outputs Slave Timing Modes Updating your Firmware Using the NI 9144 with an EtherCAT Third-Party Master Using AoE/SDO Using CoE/SDO Specifications Network Power Requirements Physical Characteristics Safety Voltages Hazardous Locations Environmental Shock and Vibration Cabling Safety Standards Electromagnetic Compatibility CE Compliance Online Product Certification RoHS Appendix A Vendor Extensions to the Object Dictionary Supported C Series Modules C Series Modules with No Configurable Options NI 9201/9221 NI 9201/9221 Scan List NI 9201/9221 Calibration Data NI 9203 NI 9203 Scan List Page NI 9203 Calibration Data Page NI 9205/9206 NI 9205/9206 Scan List Page NI 9205/9206 Calibration Data NI 9211 NI 9211 Scan List NI 9211 Calibration Data NI 9213 NI 9213 Conversion Speed Control NI 9213 Common Mode Error/Status NI 9213 Scan List NI 9213 Calibration Data NI 9215 NI 9215 Calibration Data NI 9217 NI 9217 Conversion Speed Control NI 9217 Scan List NI 9217 Calibration Data NI 9219 NI 9219 ADC Format NI 9219 Error Status NI 9219 Calibration Data Page NI 9219 Configuration Commands Page Page Page Page Page Page NI 9233 NI 9233 Configure ADC Page NI 9233 Calibration Data NI 9234 NI 9234 Configure Module Page NI 9234 Example Data Rates NI 9234 Calibration Data NI 9237 NI 9237 Configure Module Page NI 9237 Example Data Rates NI 9237 Calibration Data NI 9229/9239 NI 9229/9239 Calibration Data NI 9263 NI 9263 Calibration Data NI 9264 NI 9264 Calibration Data NI 9265 NI 9265 Error Status NI 9265 Calibration Data NI 9401 NI 9401 Direction Control NI 9403 NI 9403 Direction Control NI 9476 NI 9476 Error Status Where to Go for Support