SERVICE INSTRUCTIONS

TO CHANGE THE PANEL FILTER - Cont.

1.Park the sweeper on a smooth level surface, Turn the key switch to the “OFF” position and engage the wheel lock.

2.Disconnect the Battery Connector, which is located next to the seat.

3.Raise the Battery compartment cover and engage the safety latch.

4.Remove the rear cover.

5.Locate and remove the four wing nuts that hold the filter manifold assembly in place over the filter.

6.Disconnect the shaker motor leads and the Vac fan leads and lift the Vac Fan/Manifold assembly off thedust filter.

7.Remove and replace the dust filter.

8.Reinstall the cleaned filter and assemble the Vac Fan/Manifold Assembly to the filter.

9.Connect the shaker motor leads and the Vac fan leads.

10.Install the four Wing Nuts and tighten enough to lightly compress the gasket on the filter.

11.Reinstall the Rear cover and lower the Battery Compartment cover.

12.Reconnect the Battery and return the Sweeper to service.

FLAP SERVICE INSTRUCTIONS

The Flaps are very important to the sweeping process. Inspect the Flaps Daily and replace any flap that shows signs of wear or deterioration. The drive wheel and side flaps are adjustable and should be adjusted so there is a recommended 1/16" to 1/8" gap between the floor and the bottom edge of the flaps. The adjustable flaps have slotted mounting holes to facilitate adjustment. The Recycling flap is also an adjustable flap and should be adjusted so the flap touches the broom. The adjustment bolt is located inside the left side broom chamber door. All other flaps require no adjustment and should be replaced when worn or damaged.

WARNING

Turn Key Off Before removing Battery Connector. Disconnecting the Battery with the key switch on will produce

sparks and Could cause an Explosion.

WARNING

Always park on a level surface, turn key off, and engage wheel lock before working on the machine to keep it

from creeping or rolling.

TO ADJUST THE DRIVE WHEEL AND SIDE FLAPS

1.Park Sweeper on a smooth level surface. Turn the key switch to the “OFF” position and engage the wheel lock.

2.Disconnect the Battery Connector located next to the seat.

3.Loosen the Flap retaining screws and adjust the flap to clear the floor and leave a 1/16" to 1/8" Gap.

4.Tighten Flap retaining screws while holding flap in position.

5.Reconnect the Battery Connector.

WARNING

Turn Key Off Before removing Battery Connector. Disconnecting the Battery with the key switch on will produce

sparks and Could cause an Explosion.

 

RECYCLING FLAP

 

FLAP ADJUSTMENT

 

SCREW

C0477b

FIGURE 13

WARNING

Always park on a level surface, turn key off, and engage wheel lock before working on the machine to keep it from creeping or rolling.

TO ADJUST THE RECYCLING FLAP

1.Park Sweeper on a smooth level surface. Turn the key switch to the “OFF” position and engage the wheel lock.

2.Disconnect the Battery Connector located next to the seat.

3.Open the left side broom door and locate the recycling flap adjustment screw (See Figure 13)

4.Loosen the adjustment screw and turn the flap upwards so the flap touches the ends of the broom bristles.

5.Tighten the adjustment screw while holding the flap in place.

6.Close and Latch the left side broom door Reconnect the Battery.

American-Lincoln Technology

1-21

114 RS Operator’s Manual

 

Page 21 Page 23
Page 22
Image 22
Nilfisk-ALTO 114RS SWEEPER To Change the Panel Filter, Flap Service Instructions, To Adjust the Drive Wheel and Side Flaps
Page 21 Page 23

114RS SWEEPER specifications

The Nilfisk-ALTO 114RS Sweeper is a powerful and efficient machine designed to meet the demanding needs of commercial and industrial cleaning applications. This versatile equipment is widely recognized for its durability, ease of use, and advanced features, making it an essential tool for maintaining cleanliness in various environments such as warehouses, shopping centers, and outdoor spaces.

One of the standout features of the Nilfisk-ALTO 114RS is its robust design. Constructed with high-quality materials, this sweeper is built to withstand tough working conditions while ensuring long-lasting performance. The ergonomic design makes it easy to maneuver, even in tight spaces, allowing operators to clean large areas quickly and effectively.

The Nilfisk-ALTO 114RS is equipped with a powerful suction system that delivers excellent dust control. This technology minimizes airborne particles, providing a cleaner and healthier environment for both workers and customers. The dual filter system enhances dust collection efficiency, extending the lifespan of the filters and reducing maintenance needs.

Another notable characteristic of the 114RS is its advanced intuitive controls. The user-friendly interface simplifies operation, enabling operators to focus on cleaning rather than navigating complex settings. The adjustable sweeping speed allows for optimized performance based on the nature of the task, ensuring thorough cleaning without compromising efficiency.

In addition, the Nilfisk-ALTO 114RS features a large debris hopper that can hold a significant amount of waste, reducing the frequency of emptying and allowing for continuous operation over extended periods. The easy-to-empty hopper further enhances productivity, making it convenient for workers to dispose of collected debris quickly.

The battery-powered version of the 114RS provides the added benefit of being environmentally friendly and quieter compared to gas-powered alternatives. This makes it suitable for use in noise-sensitive areas, such as hospitals or schools, without disrupting daily activities.

Overall, the Nilfisk-ALTO 114RS Sweeper combines powerful cleaning performance, advanced technology, and user-friendly design. Its robust construction, dust control capabilities, efficient operation, and environmental considerations make it an ideal choice for businesses seeking to maintain high cleanliness standards while maximizing operational efficiency. The 114RS is not just a sweeper; it is a reliable partner in achieving a cleaner and more productive workspace.
Top Page Image Contents