OPERATING INSTRUCTIONS

TO CHARGE THE MOTIVE POWER BATTERIES (Battery powered machines only)

1.Read the detailed instructions provided on the charger.

2.Be sure all controls are “OFF” and machine is located in an area with good ventilation.

3.Open the top cover. The top cover must remain open during the charging process.

4.Disconnect the machine power supply cable from the battery using thequick disconnect provided.

5.Connect the charger cable to the battery connector.

6.Plug the charger into properly grounded AC outlet. Be sure to verify theoperating voltage of your charger. The chargers supplied with machine operate at 115 VAC @60 HZ or 230 VAC @ 50 HZ.

7.The charger will begin charging the batteries after a short period of time. The charger will shut off automati cally when the charging process is complete.

8.Unplug the charger from the grounded AC outlet before disconnecting the charger from the battery.

9.Disconnect the charger cable from the battery.

10.Check the electrolyte level in the battery after charging. Add distilled water if needed.

11.Reconnect the machine power supply cable to the battery cable.

12.Lower the top cover and perform the pre-start checks before operating the machine.

GASOLINE POWERED MACHINE FUELING INSTRUCTIONS

The fuel tank for gasoline powered machines is located on the engine. The top cover must be opened to access the fuel tank. After opening the top cover, observe the combination fuel cap/gas gauge and check the fuel level to determine if the fuel tank needs to be filled.

TO FILL THE GASOLINE POWERED MACHINE FUEL TANK

WARNING

To prevent possible fire. Never fill fuel tank while the engine is running. Always be sure gasoline container and

sweeper are electrically grounded before dispensing gas. This can be done by permanently attaching an insulated

wire with a battery clip on the end to the gasoline container.

1.Turn the key switch to the “OFF” position.

2.Open the top cover.

3.Observe the level indicated by the gas gauge on the fuel tank cap.

4.Remove the fuel tank cap from the fuel tank and add gasoline as needed.

5.Install the gas cap and lower the hinged top cover.

LP POWERED MACHINE FUELING INSTRUCTIONS

Fueling the LP powered machine is accomplished by removing the empty LP cylinder and replacing it with a full replacement cylinder. Some cylinders are equipped with a fuel level gauge. Check the gauge and change the cylinder when the gauge reads “EMPTY”. See the LP Instructions in this manual for additional information.

WARNING

Improper filling procedures could cause an explosion. Have your LP cylinders filled by qualified personnel.

WARNING

Park the machine in a safe area designated for changing LP fuel tanks. The designated safe area must have

adequate ventilation, must be free from sparks or other sources of ignition.

WARNING

NO SMOKING signs should be posted and enforced. The area must not be in the vicinity of flammables, combustible

materials or high temperature sources such as furnaces or ovens.

WARNING

Always store and transport LP fuel tanks with the safety relief valve in the up position. This will prevent the tank from venting liquid propane in the event the safety relief valve opens due to overpressure in the tank. A properly stored tank will only vent gaseous propane which dissipates much faster than liquid propane.

1-18

American-Lincoln

 

91 WS

Page 18 Page 20
Page 19
Image 19
Nilfisk-ALTO 91WS manual Gasoline Powered Machine Fueling Instructions, To Fill the Gasoline Powered Machine Fuel Tank
Page 18 Page 20

91WS specifications

The Nilfisk-ALTO 91WS is a state-of-the-art waste water vacuum system, designed to tackle both outdoor and indoor cleaning tasks across various industries. This versatile machine is particularly renowned for its impressive suction power, allowing for the effective removal of liquid waste, sludge, and debris in less time and with minimal effort.

One of the key features of the 91WS is its robust construction. Designed with durability in mind, the vacuum has a sturdy chassis and components that are resistant to wear and tear, making it ideal for demanding environments such as construction sites and heavy industry. The unit is also equipped with large wheels, ensuring ease of mobility even when fully loaded.

The 91WS incorporates advanced technology to enhance its performance. Its powerful motor delivers strong suction capabilities, while the innovative filtration system effectively separates solids from liquids, preventing clogging and maintaining optimal efficiency. The vacuum's advanced design also allows for quick and easy emptying, minimizing downtime and boosting productivity.

Another significant characteristic of the Nilfisk-ALTO 91WS is its user-friendly interface. Operators will appreciate the intuitive controls that make it simple to adjust settings and monitor performance. The vacuum is designed for easy maintenance; access to key components is straightforward, ensuring that servicing is efficient, and the machine continues to operate at peak capacity.

The 91WS also features multiple attachment options, allowing users to customize the machine for specific tasks. Whether it's cleaning up after spills or managing waste disposal, the versatility of the attachments ensures that it can handle various cleaning challenges with ease.

Safety is paramount in any industrial environment, and the Nilfisk-ALTO 91WS is designed with several safety features. The integrated float system prevents overflow, and the durable construction of the vacuum ensures that it can withstand rigorous use without posing risks to the operator.

In summary, the Nilfisk-ALTO 91WS is a powerful and versatile waste water vacuum that excels in demanding situations. With its strong performance, advanced technologies, and user-friendly features, it is an ideal solution for any business looking to optimize their cleaning processes while ensuring safety and efficiency.
Top Page Image Contents