SERVICE INSTRUCTIONS

TO CHANGE THE SIDE BROOMS

Change the side brooms when the bristles become worn to less than 3 inches length.

1.Park machine on a smooth level surface, turn key switch to “OFF” position.

2.Place the side brooms lever in the “DOWN” position.

3.Remove the pin that passes through the flange and motor shaft. Remove the broom.

4.Remove the three (3) 1/4 inch bolts and nuts that hold the broom to the motor flange.

5.Assemble the flange to the replacement broom and fasten using the hardware removed in step 4.

6.Install broom to motor shaft with the pin removed in step 3.

7.Check sweep pattern and perform height adjustment so the broom contacts the floor as shown (See Figure 16).

DUST CONTROL SERVICE INSTRUCTIONS

The dust control system consists of the filter baffle and a panel filter. The filter baffle is built in to the hopper and should be checked/cleaned when the hopper is being emptied. The panel filter is located on top of the hopper under the hinged manifold. The panel filter must be replaced if the filter media tears. Inspect the top of the panel for signs of dirt that may be escaping through tears in the filter media.

TO CLEAN THE FILTER BAFFLE

The filter baffle should be cleaned as a first step when the dust control system fails to effectively control dusting while sweeping.

1.Park the sweeper on a smooth level surface, Turn the key switch to the “OFF” position.

2.Open the top cover and disengage the filter manifold latch.

3.Lift the hinged manifold to gain access to the panel filter.

4.Remove the panel filter and inspect for debris lodged in the baffle passages.

5.Dislodge all debris from the baffle manually or with compressed air not to exceed 100 PSI.

6.Install the panel filter. Lower the manifold over the filter and engage the latch.

7.Close the top cover .

TO CLEAN THE PANEL FILTER

Clean the panel filter when the shaker fails to adequately clear the filter pleats.

1.Park the sweeper on a smooth level surface, Turn the key switch to the “OFF” position.

2.Open the top cover and disengage the vacuum manifold latch.

3.Lift the hinged vacuum manifold to gain access to the panel filter.

4.Remove the panel filter and inspect for damage. Replace if not in serviceable condition.

5.Apply compressed air not to exceed 100 PSI to the top side of the panel to backflush lodged dirt from the filter media. The filter may also be cleaned with a solution of soap and water. If this method is used, do not use the panel filter until it has completely dried.

6.Reinstall the cleaned filter and lower the hinged manifold assembly over the filter.

7.Engage the manifold latch and close the top cover.

TO CHANGE THE PANEL FILTER

Change the filter when obvious damage is evident. Inspect for leakage or a heavily loaded filter to the point that cleaning and shaking of the filter has no effect on clearing the pleats.

1.Park the sweeper on a smooth level surface, Turn the key switch to the “OFF” position.

2.Open the top cover and disengage the vacuum manifold latch.

3.Lift the hinged vacuum manifold to gain access to the panel filter.

4.Remove the panel filter and install a new replacement panel.

5.Lower the hinged manifold assembly over the filter.

6.Engage the manifold latch and close the top cover.

1-26

American-Lincoln

 

91 WS

Page 27
Image 27
Nilfisk-ALTO 91WS manual To Change the Side Brooms, Dust Control Service Instructions, To Clean the Filter Baffle

91WS specifications

The Nilfisk-ALTO 91WS is a state-of-the-art waste water vacuum system, designed to tackle both outdoor and indoor cleaning tasks across various industries. This versatile machine is particularly renowned for its impressive suction power, allowing for the effective removal of liquid waste, sludge, and debris in less time and with minimal effort.

One of the key features of the 91WS is its robust construction. Designed with durability in mind, the vacuum has a sturdy chassis and components that are resistant to wear and tear, making it ideal for demanding environments such as construction sites and heavy industry. The unit is also equipped with large wheels, ensuring ease of mobility even when fully loaded.

The 91WS incorporates advanced technology to enhance its performance. Its powerful motor delivers strong suction capabilities, while the innovative filtration system effectively separates solids from liquids, preventing clogging and maintaining optimal efficiency. The vacuum's advanced design also allows for quick and easy emptying, minimizing downtime and boosting productivity.

Another significant characteristic of the Nilfisk-ALTO 91WS is its user-friendly interface. Operators will appreciate the intuitive controls that make it simple to adjust settings and monitor performance. The vacuum is designed for easy maintenance; access to key components is straightforward, ensuring that servicing is efficient, and the machine continues to operate at peak capacity.

The 91WS also features multiple attachment options, allowing users to customize the machine for specific tasks. Whether it's cleaning up after spills or managing waste disposal, the versatility of the attachments ensures that it can handle various cleaning challenges with ease.

Safety is paramount in any industrial environment, and the Nilfisk-ALTO 91WS is designed with several safety features. The integrated float system prevents overflow, and the durable construction of the vacuum ensures that it can withstand rigorous use without posing risks to the operator.

In summary, the Nilfisk-ALTO 91WS is a powerful and versatile waste water vacuum that excels in demanding situations. With its strong performance, advanced technologies, and user-friendly features, it is an ideal solution for any business looking to optimize their cleaning processes while ensuring safety and efficiency.