4. Cut the plastic tie holding the Upright Wire Harness (98). | 4 |
|
| ||
Have a second person hold the Handrails (66) near the |
|
| |||
|
| 81 | |||
Uprights (69). Connect the Upright Wire Harness to the |
|
| |||
|
|
| |||
wires extending from the Console Base (81). | The connec- |
|
| ||
tors should slide together easily and snap into place. |
|
| 98 | ||
If they do not, turn one connector and try again. | Then, |
|
| ||
insert the connectors and the Upright Wire Harness into |
|
|
| ||
the hole in the right Upright. Set the Handrails on the |
|
|
| ||
Uprights, being careful not to pinch the wires. |
|
|
| ||
5. Insert two Handrail Bolts (78) with Handrail Spacers (77) |
| 66 | 69 | ||
|
|
| |||
into the right Upright (69) and the right Handrail (66). | Be |
|
| ||
careful not to pinch the wires. | Make sure that the |
|
| ||
Handrail Spacers are flush against the right Upright, with | 5 |
|
| ||
the thick sides facing the center of the treadmill, as shown |
|
| |||
|
|
| |||
in the inset drawing. Next, lift the right Handrail (66) slightly |
|
|
| ||
and align the Bolts with the holes in the Handrail. Thread |
|
|
| ||
the Bolts into the Handrail. | Do not tighten the Bolts yet. |
| 69 | ||
|
|
|
|
| |
Attach the left Handrail (not shown) in the same way. |
| 66 | 77 | ||
Then, | tighten all four Handrail Bolts (78). |
| Thick | ||
|
| ||||
|
|
|
|
| |
6. Make sure that all parts are properly tightened before |
|
| Side | ||
|
|
| |||
you use the treadmill. Place a mat beneath the tread- |
| 77 | 78 | ||
mill to protect the floor. |
|
|
|
| |
If you purchase the optional chest pulse sensor (see | 1 | 82 |
| ||
page 21), follow the steps below to install the receiver |
| ||||
included with the chest pulse sensor. |
|
|
|
| |
1. Make sure that the power cord is unplugged. | Remove |
|
| ||
the indicated screws from the Console Back (88). |
|
|
| ||
(Important: The screws may be different lengths; note |
|
|
| ||
the original locations of the screws.) | Next, remove the | 88 |
| ||
Console Back. |
|
|
| ||
|
|
| Screws | ||
|
|
|
|
| |
2. Peel the paper off the pad on the bottom of the Receiver |
| 2 | ||
(A).Turn the Receiver so the cylinder is on the side |
|
| ||
shown, | and press the Receiver into the Console Base (81) |
| ||
in the indicated location. |
| A | ||
|
|
| ||
|
|
| Cylinder | |
|
|
| 81 | |
3. Connect the included Short Jumper Wire (B) to the wire on |
| 3 | ||
the Receiver (A). Connect the other end of the Short |
| |||
| PLS2 | |||
Jumper Wire to the PLS2 jack on the underside of the |
| |||
| Jack | |||
Console (82). (Note: If there is already a wire in the PLS2 | ||||
82 | ||||
jack, unplug it.) Discard the other wires included with the | ||||
receiver. Use the included wire tie to secure the wires, if |
|
| ||
needed. |
|
|
| |
Make sure that no wires are pinched. | See step 1. | |||
Reattach the Console (82) with the screws. |
| Important: If | ||
the screws are not in their original locations, the |
| B | ||
Console may be damaged. |
| |||
|
|
| A | |
7
