Nortel Networks 5625HD Installing the Switch Module

Using the Model 5625HD EtherSpeed Switch Module

3-6 206208-A

Installing the Switch Module

To install and secure the Model 5625HD switch module in the chassis:

1. Remove the filler panel from the chassis slot where you intend to install

the module.

2. Extend the switch module ins erter/extractor levers to the vertica l position

(Figure3-3).

Figure 3-3. Inserter/Extractor Levers in Vertical Position

3. Align the top and bottom edges of the metal printed circuit board carrier

with the slot card guides at the top and bottom of the slot.

4. Slide the switch module into the chassis until you feel it engage the

backplane (Figure 3-4).

The inserter/extractor levers should still be in the vertical position and in

contact with the front of the chassis. Do not push the switch module all the

way into the chassis.

Note: These instructions illustrate installing a Model 5625HD switch module

in a Model 5000BH/BHC chassis. The instructions also apply to a Model

5005BH chassis.

4689

Contents

Main ii Copyright 1999 Nortel Networks Trademarks Statement of Conditions USA Requirements Only European Requirements Only Japan/Nippon Requirements Only Taiwan Requirements Canada Requirements Only Nortel Networks Software License Agreement iv Page Page Contents Page Page Page Figures Page Page Page Preface Before You Begin Related Publications Page How to Get Help Chapter 1 Overview of the Model 5625HD Switch Module Overview of the EtherSpeedII Switch Module Page Features of the Model 5625HD Switch Module Page Overview of the Model 5625HD Switch Module 206208-A 1-5 Physical Description Figure 1-2. Model 5625HD EtherSpeedII 24-Port Autonegotiating Switch Module Switch Configuration and Management Spanning Tree Protocol 802.1d Support Support for Virtual LANs Filtering Hot-Swapping Capability About the Model 500xBH/BHC Backplane 1-10 LEDs Port LEDs Figure 1-5. LEDs on the Model 5625HD Switch Module 10/100 Mb/s UTP Autonegotiation Ports 5625HD Page Connecting to Ethernet Hubs and Network Devices Network Configuration Examples 2-4 Figure 2-1. Network Example Giving a Server a Dedicated Port 2-6 Replacing a Bridge Figure 2-3. Replacing a Bridge Desktop Switch with ATM Uplinks 2-8 Figure 2-4. Desktop Switch with ATM Uplinks Segment Switch in an Enterprise Network Desktop Switch and Frame-to-Cell Converter Multi-Link Trunking Default Port Configuration Predefined SpeedView Configurations Chapter 3 Installing the Model 5625HD Switch Module Arranging Modules in a Model 500xBH/BHC Chassis Page Page Required Tools and Equipment Installing the Switch Module Page Checking LEDs Making 10/100 Mb/s Connections Connecting Terminals and Management Stations Page Checking the Module Connection to the Backplane Removing and Replacing the Switch Module Conditions for Replacing a Switch Module Removing a Switch Module Installing the Replacement Switch Module Reconfiguring the Replacement Switch Module Page Chapter 4 Troubleshooting Preliminary Steps Previous Module Configuration Incompatibility Model 5625HD Switch Module Startup Failure Port Connection Problems Page Page Appendix A Technical Specifications Using the Model 5625HD EtherSpeed Switch Module A-2 Technical Specifications Page Appendix B Cables and Connectors UTP Cable Length Limitations UTP Cabling 10BASE-T/100BASE-TX MDI Ports and MDI-X Ports Page B-4 UTP Cables and Connectors Figure B-3. 10BASE-T/100BASE-TX Ethernet UTP Crossover Cable TableB-1. 10BASE-T/100BASE-TX MDI-X Port Pin Assignments Using Category 5 Unshielded Twisted Pair Cables Using Shielded Twisted Pair Cables 206208-A C-1 Port LEDs Appendix C LEDs Figure C-1. LED Display for the Model 5625HD Switch Module 5625HD 10/100 Switch Host Port Status C-2 TableC-1. LEDs on the Model 5625HD Switch Module RJ-45 LEDs Page Index Numbers A B C D E F H I R S T U V