90 Chapter 7 Setting media bay module DIP switches
N0008587 01
Table 11 shows possible DS30 bus numbers and offset configurations for each type of module, and the corresponding switch settings for modules that only allow single density, or which are set to single density, as may be the case for a DSM16+ or DSM32+. The ASM/ASM8 settings are the same for either single or double density, except that you can only use offset 0 and 1 on a DS30 bus that is not set for double density, such as for DS30 06 and 07 on a PDD system.For FEM settings, refer to “FEM switch settings” on page 108. DECT module dip switch settings are described in the DECT documentation which is available on the documentation CD from previous releases of BCM.Example: Position your DSM 16 module (step 1), which requires one full DS30 bus (step 2), in DS30 02 (step 3). Moving across, note that the offset is 0 (step 4). Set the DIP switches on the module to match the DIP switch settings indicated for that offset (step 5).
Table 11 Possible media bay module DIP switch settings, single density
DS30
bus
#Offsets
Media bay module positioning DIP switch settings
DSM
16/
16+
Offsets
0
DSM
32/
32+
Offsets
0
4x16
Offsets
0,1, 2, 3
Line Exten.
ASM 8/
GASM8
Offsets
0, 1, 2
DTM
Offsets
0
CTM/
GATM4
Offsets
0, 1, 2, 3
CTM 8/
GATM8
Offsets
0, 1, 2
BRI
Offsets
0, 1, 2, 3
12 3
(offset)
456
(DS30)
2
00 0 0 Picks
up
ch.
#3
0 0 0 0 0 on on on on on on
11 1 1 1 on on off on on on
22 1 2 2 2 on off on on on on
33 3 on off off on on on
3
00 0 0 Picks
up
ch.
#4
0 0 0 0 0 on on on on on off
11 1 1 1 on on off on on off
22 1 2 2 2 on off on on on off
33 3 on off off on on off
4
00 0 0 Picks
up
ch.
#5
0 0 0 0 0 on on on on off on
11 1 1 1 on on off on off on
22 1 2 2 2 on off on on off on
33 3 on off off on off on
5
00 0 0 Picks
up
ch.
#6
0 0 0 0 0 on on on on off off
11 1 1 1 on on off on off off
22 1 2 2 2 on off on on off off
33 3 on off off on off off
6
00 0 0 Picks
up
ch.
#7
0 0 0 0 0 on on on off on on
11 1 1 1 on on off off on on
22 1 2 2 2 on off on off on on
33 3 on off off off on on
7***
00
Not
supported
0 0 0 0 0 on on on off on off
11 1 1 on on off off on off
21 2 2 2 on off on off on off
33 on off off off on off
Module set to offset 0 Modul e set to offset 1 Module set to offset 2 Module set to offset 3
Each shaded square represents the amount of the DS30 bus, and the offset, which the module requires.
***If your system is configured with a 3/5 DS30 split, DS30 07 is not available to media bay modules.