Oceanic Pro Plus 2 Inspection, BatteryHatchInstallation

BatteryHatchInstallation

•Ensure that the Battery is properly oriented and the Hatch O-ring is evenly seated.

•Carefully place the Battery Hatch into position so that it seats on top of the O-ring, and while holding it in place, secure it with the 4 screws by turning them clockwise.

DO NOT attempt to use any other screws.

•Carefully tighten the screws by alternately turning them each one turn at a time (Fig. 99). Turn the upper left one (a), then the lower right (b), then the lower left (c), then the upper right (d).

•Repeat the sequence until all of the screws are evenly secure. The outer surface of the Battery Hatch should be flush with the outer surface of the Housing. DO NOT overtighten.

Inspection

•Activate the unit and watch carefully as it performs a full diagnostic and battery check, and enters Surface Mode. Observe the LCD display to ensure it is consistently clear and sharp in contrast throughout the screen.

•If any portions of the display are missing or appear dim, or if a Low Battery Condition is indicated, return your Pro Plus 2 to an Authorized Oceanic Dealer for a complete evaluation before attempting to use it.

X	a	d X
X	c	b X

Fig.99 -HatchInstallation

89

Contents

Pro Plus dive computer Page CONTENTS CONTENTS (continued) Payspecialattentiontoitemsmarked withthisWarningsymbol PRO PLUS FEATURES and DISPLAYS INTRODUCTION INTERACTIVE CONTROL CONSOLE Advance Select BAR GRAPHS Tissue Loading Bar Graph (TLBG) OxygenAccumulationBarGraph(O2BG) VariableAscentRateIndicator(VARI) WARNING: At depths greater than 60 feet (18 Air Time Remaining Bar Graph (ATRBG) DIVETIMEREMAINING ALPHA / NUMERIC DISPLAYS CylinderPressureDisplay DepthDisplays Current Depth Maximum Depth TimeandDate Displays Time displays Main Time second time Date AUDIBLEALARM LEDWarningLight A single short beep (which cannot be disabled) is emitted for the following Page SMARTGLO® BACKLIGHT POWER SUPPLY Battery Indicator LowBatteryCondition FO2MODE FO2 value of 'Air value of 21% FO250%Default If the Default function is set to ON Page ACTIVATION and SETUP ACTIVATION To Activate the Pro Plus 2, press and release the Left (Advance) Button Backup Activation SURFACEMODE To activate the Backlight: AccessingOtherModes SET MODES Set Mode Access Timing ENTERING SETTINGS -SETMODE #1 TO SET - FO2 FO2 TO SET - MAX DEPTH ALARM 1 more time FEET MAX dEEP Max Depth TO SET - ELAPSED DIVE TIME ALARM 2 more times EdT Elapsed Dive Time PC INTERFACE To download data 3 more times ENTERING SETTINGS -SETMODE #2 TO SET - UNITS OF MEASURE TO SET - HOUR FORMAT Hour TO SET - TIME Minute TO SET - DATE dAY Year Month Day TO SET - AUDIBLE ALARM 7 more times ALM Page TO SET - AIR TIME REMAINING BAR GRAPH ALARM(while in the Surface Mode) 9 more times Atr Air Time Remaining Bar Graph TO SET - TURN PRESSURE ALARM 10 more times TO SET - END PRESSURE ALARM 11 more times TO SET - DIVE TIME REMAINING ALARM 12 more times dtr Dive Time Remaining TO SET - MAXIMUM PO2 ALARM 13 more times PO2 TO SET - FO2 50% DEFAULT 14 more times TO SET - BACKLIGHT DURATION 15 more times GLO Dura- tion TO SET - PC SAMPLING RATE 16 more times SECS Sampling Rate TO SET - USER SET DIGITAL GAUGE MODE(while in the Surface Mode) 17 more times GAU OFF TO SET - WATER ACTIVATION 18 more times ACT H20 PLAN and DIVE MODES Page To access the Pre Dive Planning Sequence 1 time TISSUE LOADING BAR GRAPH (Fig. 45a) OXYGEN ACCUMULATION BAR GRAPH (Fig. 46a) VARIABLE ASCENT RATE INDICATOR (Fig. 46b) TOO FAST AIR TIME REMAINING BAR GRAPH CONTROL OF DISPLAYS Backlight NODECOMPRESSIONDIVEMODE No Decompression Dive Mode - Display #1 (Fig. 49) No Decompression Dive Mode - Display #2 (Fig. 50) No Decompression Dive Mode - Display #3 (Fig. 51) No Decompression Dive Mode - Display #4 (Fig. 52) NoDecompressionDiveMode-SecondaryDisplay (Fig. 53) No Decompression Dive Mode - SAFETY STOP (Fig. 54) DECOMPRESSIONDIVEMODE Total Ascent Time ManagingDecompressionStops DecompressionDiveMode-MainDisplay#1 Page VIOLATIONMODES ConditionalViolationMode(Fig.60) If you ascend shallower (Fig. 60a) than a Required Decompression Ceiling Stop Depth Penalty Time DelayedViolationMode#1(Fig. 61) If you remain above the Required Ceiling Stop Page ImmediateViolationModeandGaugeMode Immediate Violation Mode Gauge Mode Page HIGH PO2 DIVE MODE 1.40 ATA, or 0.2 ATA less than the PO2 Alarm set point (a user setting); Page USER SET DIGITAL GAUGE MODE UNEXPECTED LOSS OF DISPLAYED INFORMATION POST DIVE MODES POST DIVE SURFACE MODE TRANSITION PERIOD To view that dive's Log(Fig. 72) again Page 2 times To access the Time to Desaturation Countdown 3 times LOGMODE Log Button Control in Log Mode To access the Log Mode and view the First Screen(While in Surface Mode) 4 times To view the Second Screen of the Log (Nitrogen data) To view the Third Screen of the Log (Oxygen data) To access the first screen of the previous dive's Log AFTER THE FIRST 2 HOURS To access other modes or enter settings WET CONTACTS H2O DOWNLOADING DATA TO A PC SIMULATOR (DEMO) MODE SIMULATORMODE Access and Setup SIM DEMO: NI-O2 CUR NEW DEMO: PSI Demo Surface Mode DEMO: FO2 Air DemoDiveMode Demo Dive Mode Descending Descent Time Acceleration Ascending Ascent Rate UP Arrow SurfacingfromaSimulatedDive Page GENERAL CARE AND CLEANING INSPECTIONS AND SERVICE inspected annually ToObtainService: BATTERY REPLACEMENT Hot Swap BatteryRemoval MoistureintheBatteryCompartment BatteryInstallation new BatteryHatchInstallation Inspection SPECIFICATIONS SPECIFICATIONS(CONTINUED) Page Page Page Page OCEANIC WORLD WIDE INSPECTION / SERVICE RECORD NOTES RESET FEATURE RESET PROCEDURE