FLR Flow Transmitter
Installation & Programming Instructions
Table 1 - Dimensions
|
| A | B | C | D | E | F | G | H | I | J | K |
Nominal | Length | Length | Length | Width | Width | Width | Width | Depth | Offset | Hole Dia. | ||
Port Size | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | in. (mm) | ||
|
|
|
|
|
|
|
|
|
|
| ||
1/4 (SAE 6) | 6.60 (168) | 5.27 (134) | 6.41 (163) | 6.00 (152) | 3.23 (82) | 3.00 (76) | 4.20 (107) | 2.94 (75) | 1.51 (38) | .31 (8) | ||
|
|
|
|
|
|
|
|
|
|
|
| |
1/2 | (SAE 10) | 6.60 (168) | 5.27 (134) | 6.41 (163) | 6.00 (152) | 3.23 (82) | 3.00 (76) | 4.20 (107) | 2.94 (75) | 1.51 (38) | .31 (8) | |
|
|
|
|
|
|
|
|
|
|
|
| |
3/4 | (SAE 12) | 7.20 (183) | 5.27 (134) | 7.04 (179) | 6.00 (152) | 3.60 (91) | 3.00 (76) | 4.20 (107) | 2.94 (75) | 1.27 (32) | .31 (8) | |
|
|
|
|
|
|
|
|
|
|
| ||
1 (SAE 16) | 7.20 (183) | 5.27 (134) | 7.04 (179) | 6.00 (152) | 3.60 (91) | 3.00 (76) | 4.20 (107) | 2.94 (75) | 1.27 (32) | .31 (8) | ||
|
|
|
|
|
|
|
|
|
|
|
| |
(SAE 20) | 12.20 (310) | 10.68 (271) | 11.65 (296) | 7.63 (194) | 4.84 (123) | 3.82 (97) | 5.02 (128) | 4.50 (114) | 2.20 (56) | .31 (8) | ||
|
|
|
|
|
|
|
|
|
|
|
| |
(SAE 24) | 12.20 (310) | 10.68 (271) | 11.65 (296) | 7.63 (194) | 4.84 (123) | 3.82 (97) | 5.02 (128) | 4.50 (114) | 2.20 (56) | .31 (8) | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
®
FLR
III. INSTALLATION
This unit should be installed and serviced by technically qualified personnel trained in maintaining industrial class flow instrumentation and processing equipment.
WARNING
Disconnect electrical power before opening wiring enclo- sure. Failure to follow these instructions could result in serious personal injury or death and/or damage to the equipment.
WARNING
All wiring should be installed in accordance with the National Electrical Code and must conform to any applicable state and local codes. Failure to follow these instructions could result in serious personal injury or death and/or damage to the equipment.
CAUTION
Air/gas transmitters are NOT oxygen cleaned. Use with oxygen may cause hazardous or explosive con- ditions that may cause serious personal injury and/or equipment damage.
CAUTION
This transmitter may contain residual amounts of test fluid at the time of shipment. This fluid should be removed prior to installation as the fluid may be incompatible or hazardous with some liquids or gases. Failure to follow these instructions could result in damage to the equipment.
CAUTION
This standard transmitter is unidirectional. Attempts to flow fluids in the opposite direction of the flow arrow will result in the meter acting as a check valve, creating a deadheading situation. If the differential pressure magnitude is great enough, damage to the internal parts of the meter will result.
Page 3
