Manuals / Omron / Power Tools / Stud Sensor

Omron ZS-MDC Control keys, Mode Switch, Threshold Selector Switch, LOW indicator, Pass indicator

Models: ZS-MDC

1 94

Download 94 pages 46.89 Kb

Page 23

Section 1

Part Names and Functions

(7)Control keys

The Control Keys are for setting measurement conditions and other information. The functions assigned to the Control Keys change according to the operating mode.

Displays and Key Operations p.3-5

(8)Mode Switch

The Mode Switch selects the operating mode.

RUN mode	: Select this mode when performing regular measurement.
TEACH mode	: Select this mode when setting the judgment thresholds.
FUN mode	: Select this mode when setting measurement conditions.

(9)Threshold Selector Switch

The Threshold Selector switch selects whether to set (or display) the HIGH or LOW threshold.

(10)LOW indicator

The LOW indicator lits when the condition “measured value < LOW threshold” is satisfied.

(11)PASS indicator

The PASS indicator lits when the condition “LOW threshold ≤ measured value ≤ HIGH threshold” is satisfied.

(12)HIGH indicator

The HIGH indicator lits when the condition “HIGH threshold < measured value” is satisfied.

(13)Coupler

This connector is for connecting the Multi-Controller to the Sensor Controller.

(14)RS-232C connector

Connect the RS-232 cable when you are connecting the Multi-Controller to a personal computer that does not have a USB port.

(15)Voltage/Current switch

The Voltage/Current switch selects between voltage output and current output.

Before operating this switch, make sure that the Multi-Controller is turned OFF. Also, make sure that the load connected to “linear output wire (co-axial) — linear GND wire” satisfies the rating of the set state (voltage or current output) before turning the Multi-Controller ON. Otherwise, the Multi-Controller may be damaged.

Rating of connected load (I/O Circuit Diagrams) p.2-12

(16)I/O Cable

The I/O cable connects the Sensor Controller to the power supply and external devices, such as timing sensors or programmable controllers.

(17)USB port

Connect the USB cable to the USB port to connect to a personal computer.

ZS-MDC

User’s Manual

Section 1 FEATURES

1-9

Image 23

Omron ZS-MDC Control keys, Mode Switch, Threshold Selector Switch, LOW indicator, Pass indicator, High indicator, Coupler

Contents

Smart Sensor Introduction How to Switch the Display Language to EnglishSmart Sensors Multi-Controller ZS-MDC EctionRead and Understand this Document Suitability for USE Dimensions and Weights Others Installation EnvironmentPower Supply and Wiring Installation Site Precautions for Correct UseWarming Up Orientation when Installing the Multi-ControllerMaintenance and Inspection Format Editors NoteVisual Aids Meaning of SymbolsMemo Contents Introduction Contents Features Completely Digitally Based Logic Operation Processing Multi-Controller FeaturesSupports Connection to Up to 9 Sensor Controllers Wide Range of Logic Operation FunctionsDedicated Software SmartMonitor Zero Same Compact Size as Sensor ControllerUSB Connection Measurement of Average Workpiece Height Multi-Controller ApplicationsMeasurement of Workpiece Thickness at Multiple Locations Measurement of Stepped WorkpiecesBatch-acquisition of Multi-point Measurement Data Measurement of Workpiece FlatnessMeasurement of Workpiece Strain State of gang-mounted Sensor Controllers can be monitored Gang-mounted Sensor Controllers can be set upZS-MDC11/MDC41 Basic ConfigurationPart Names and Functions Pass indicator Mode SwitchThreshold Selector Switch LOW indicatorMemo Installation & Connection Installation & ConnectionAbout the power supply About Installation and ConnectionChecking the installation environment Checking the installation siteAttaching the ferrite core Multi-ControllerCH0 CH1 CH2 CH3 CH9 Installing the Multi-ControllerAbout channel No. when controllers are gang-mounted PFP-M Installing on the DIN trackInstallation procedure Install the cover on the coupler of the controller Open the connector cover on the con- trollerRemoval procedure Installation & Connection Mounting on a panel InstallationHook the hooks of the mounting fixture Install the Multi-Controller and SensorController with Panel Mount Adapters Attached onto the panel from the frontAbout the I/O cable Wiring the I/O cableLinear GND OUT3 Enable outputOUT4 Busy output Linear outputNPN type ZS-MDC11 Installation & Connection Circuit DiagramsPNP type ZS-MDC41 Memo Setup Installation and Connection Setting FlowWhen a Problem Occurs Basic Knowledge for Operation About SetupSwitching Modes Displays and Key Operations FUN ModePress the Menu key to return to the top menu Press function key 2 representing onResolu RUN ModeThresh Voltage CurrentTeaching Direct Teach ModeWhen TASK1 is selected List of Setting ItemsFUN Mode SET NO-MEAS TimerAdjust COM ModeBank System When other than TASK1 is selectedTeach Mode RUN ModeSelecting Tasks Setting Assignments Setting Logic Operation Methods Switching banks by external signal input Setting I/O AssignmentsTASK3 TASK4 Changing Output AssignmentsChanging Linear Output Assignments About Digital OutputMemo Application Setting Examples Application Setting ExamplesExamples Application SettingSet the expression of TASK1 Select TASK1SENSING-CALC-CALC-MAX-MIN Application Measuring the Relative Difference between StepsSet the expression of TASK1 Following the same procedure as 2 to 3, set Up TASK3To linear-output the operation result I/O SET-I/O SET-ANALOG Measuring the Reference Difference between Steps Details to be output Following the same procedure as 2 to 3, set Up TASK2Select TASK1 or TASK2 depending on CH0 CH1 CH2 CH3 CH9 Measuring FlatnessTASK12 TASK2 TASK34 TASK4 Input a Input B Input C Measuring the Average Height Select TASK1 so that the average value can be linear-output Average to ON, and other inputs to OFFCH0 CH1 CH2 CH3 CH4 Measuring the Twist of a WorkpieceInput X Input D Input Y Input C Select TASK3 so that the twist value can be linear-output Select TASK3 so that the judgment on the twist can be outputCH0 CH1 CH2 CH3 Measuring the Warp of a WorkpieceSelect TASK1 Application Setting Examples Select TASK2 so that the warp value can be linear-output Select TASK2 so that the judgment on the warp can be outputMemo Appendix Troubleshooting Others Error Messages and CountermeasuresWhen Error Is Displayed on the Main Display When all digits on the main display and sub-display blinkOr more of the rated measuring range Glossary Multi-Controller Specifications and External DimensionsPASS/LOW ZS-MDC11 ZS-MDC41Shock resistance destructive ZS-XPM1/XPM2 Panel Mount AdaptersZS-XRS2 RS-232C Cable for Connecting to a Personal ComputerZS-XCN Controller Link UnitVer1.50 to Ver2.00 Version Up InformationVer1.00 to Ver1.50 Section Index IndexUSB Memo Z209-E1-01 Revision HistoryTerms and Conditions of Sale Omron Electronics LLC