Manuals / Omron / Power Tools / Stud Sensor

Omron user manual PNP type ZS-MDC41

Models: ZS-MDC

1 94

Download 94 pages 46.89 Kb

Page 37

Section 2

About the I/O cable

●PNP type (ZS-MDC41)

	Brown	DC24V
	Red	OUT0
	Green OUT1
			Load
	Black	OUT2
			Load
	Pink	OUT3
			Load
	Gray	OUT4
		Load	DC
			24V
		Load
	Blue GND(0V)
circuits	Yellow	IN0
	Light blue IN1

Internal	Purple	IN2
Internal
	White	IN3
	Orange

Current output 4 to 20 mA

Current voltage/		Co-axial (black)	Linear output
output selector switch
	40Ω	Voltage output			Current output: 300 Ω or less
	40Ω	Voltage output		Load	Current output: 300 Ω or less
				Load	Voltage output: 10 kΩ or more
		10 V			Voltage output: 10 kΩ or more
		10 V
		Shielded	Linear GND
		Shielded	Linear GND

Section 2 INSTALLATION & CONNECTION

ZS-MDC

User’s Manual

2-13

Image 37

Omron user manual PNP type ZS-MDC41

Contents

Smart Sensor Introduction How to Switch the Display Language to EnglishSmart Sensors Multi-Controller ZS-MDC EctionRead and Understand this Document Suitability for USE Dimensions and Weights Power Supply and Wiring Installation EnvironmentOthers Installation Site Precautions for Correct UseMaintenance and Inspection Orientation when Installing the Multi-ControllerWarming Up Format Editors NoteVisual Aids Meaning of SymbolsMemo Contents Introduction Contents Features Supports Connection to Up to 9 Sensor Controllers Multi-Controller FeaturesWide Range of Logic Operation Functions Completely Digitally Based Logic Operation ProcessingUSB Connection Same Compact Size as Sensor ControllerDedicated Software SmartMonitor Zero Measurement of Workpiece Thickness at Multiple Locations Multi-Controller ApplicationsMeasurement of Stepped Workpieces Measurement of Average Workpiece HeightMeasurement of Workpiece Strain Measurement of Workpiece FlatnessBatch-acquisition of Multi-point Measurement Data State of gang-mounted Sensor Controllers can be monitored Gang-mounted Sensor Controllers can be set upZS-MDC11/MDC41 Basic ConfigurationPart Names and Functions Threshold Selector Switch Mode SwitchLOW indicator Pass indicatorMemo Installation & Connection Installation & ConnectionChecking the installation environment About Installation and ConnectionChecking the installation site About the power supplyAttaching the ferrite core Multi-ControllerAbout channel No. when controllers are gang-mounted Installing the Multi-ControllerCH0 CH1 CH2 CH3 CH9 Installation procedure Installing on the DIN trackPFP-M Removal procedure Open the connector cover on the con- trollerInstall the cover on the coupler of the controller Installation & Connection Mounting on a panel InstallationController with Panel Mount Adapters Install the Multi-Controller and SensorAttached onto the panel from the front Hook the hooks of the mounting fixtureAbout the I/O cable Wiring the I/O cableOUT4 Busy output OUT3 Enable outputLinear output Linear GNDNPN type ZS-MDC11 Installation & Connection Circuit DiagramsPNP type ZS-MDC41 Memo Setup Installation and Connection Setting FlowWhen a Problem Occurs Switching Modes About SetupBasic Knowledge for Operation Displays and Key Operations FUN ModePress the Menu key to return to the top menu Press function key 2 representing onThresh RUN ModeVoltage Current ResoluTeaching Direct Teach ModeFUN Mode List of Setting ItemsWhen TASK1 is selected Adjust TimerCOM Mode SET NO-MEASBank System When other than TASK1 is selectedTeach Mode RUN ModeSelecting Tasks Setting Assignments Setting Logic Operation Methods Switching banks by external signal input Setting I/O AssignmentsChanging Linear Output Assignments Changing Output AssignmentsAbout Digital Output TASK3 TASK4Memo Application Setting Examples Application Setting ExamplesExamples Application SettingSet the expression of TASK1 Select TASK1SENSING-CALC-CALC-MAX-MIN Application Measuring the Relative Difference between StepsSet the expression of TASK1 Following the same procedure as 2 to 3, set Up TASK3To linear-output the operation result I/O SET-I/O SET-ANALOG Measuring the Reference Difference between Steps Select TASK1 or TASK2 depending on Following the same procedure as 2 to 3, set Up TASK2Details to be output CH0 CH1 CH2 CH3 CH9 Measuring FlatnessTASK12 TASK2 TASK34 TASK4 Input a Input B Input C Measuring the Average Height Select TASK1 so that the average value can be linear-output Average to ON, and other inputs to OFFCH0 CH1 CH2 CH3 CH4 Measuring the Twist of a WorkpieceInput X Input D Input Y Input C Select TASK3 so that the twist value can be linear-output Select TASK3 so that the judgment on the twist can be outputCH0 CH1 CH2 CH3 Measuring the Warp of a WorkpieceSelect TASK1 Application Setting Examples Select TASK2 so that the warp value can be linear-output Select TASK2 so that the judgment on the warp can be outputMemo Appendix Troubleshooting When Error Is Displayed on the Main Display Error Messages and CountermeasuresWhen all digits on the main display and sub-display blink OthersOr more of the rated measuring range Glossary Multi-Controller Specifications and External DimensionsPASS/LOW ZS-MDC11 ZS-MDC41Shock resistance destructive ZS-XPM1/XPM2 Panel Mount AdaptersZS-XRS2 RS-232C Cable for Connecting to a Personal ComputerZS-XCN Controller Link UnitVer1.00 to Ver1.50 Version Up InformationVer1.50 to Ver2.00 Section Index IndexUSB Memo Z209-E1-01 Revision HistoryTerms and Conditions of Sale Omron Electronics LLC