Onkyo DV-SP1000 instruction manual Ir In/Out, MIX Audio OUT 30, 31, Surr Mode Audio OUT switch

Getting to Know the DV-SP1000/DV-SP1000E—Continued

GVIDEO OUT S VIDEO (30)

These two sockets output S-Video and can be con- nected to an S-Video input on a TV or projector.

HVIDEO OUT VIDEO (30)

These two sockets output composite video and can be connected to a composite video input on a TV or projector.

IDIGITAL 1 AUDIO OUT (36, 38)

These sockets output digital audio and can be con- nected to the digital audio input on a hi-fi amp, AV receiver, surround sound decoder (Dolby Digital, DTS), or other component. There’s a coaxial output and an optical output.

JDIGITAL 2 AUDIO OUT (36, 38)

These sockets output digital audio and can be con- nected to the digital audio inputs on a hi-fi amp, AV receiver, surround sound decoder (Dolby Digital, DTS), or other component. There’s a coaxial output and an optical output.

KIR IN/OUT (40)

The IR IN socket can be used to connect a commer- cially available IR receiver, which can be used to pickup signals from the remote controller when the DV-SP1000/DV-SP1000E is located in another room, installed in a rack, or is out of range of the remote controller

The IR OUT connector can be used to connect a commercially available IR emitter, which can be used to pass remote controller signals received by the IR IN along to other components.

L REMOTE CONTROL (40)

These (Remote Interactive) sockets can be con-

nected to the sockets on other Onkyo AV com- ponents for interactive control.

To use you must make an analog audio connec- tion between the DV-SP1000/DV-SP1000E and your Onkyo AV receiver, even if they are connected digitally.

MD.MIX AUDIO OUT (30, 31, 38)

These sockets output analog audio and can be con- nected to a stereo analog audio input on a TV, hi-fi amp, or other component. If the source audio is multichannel (Dolby Digital, DTS, DVD-Audio, SACD), they output a 2-channel downmix.

NFRONT, SURR 1, CENTER & SUBWOOFER AUDIO OUT (37)

These sockets output 5.1-channel analog audio and can be connected to a 5.1-channel analog audio input on an AV receiver, surround sound decoder (Dolby Pro Logic), or other component.

OSURR 2 AUDIO OUT (37)

These sockets output the same analog audio as the SURR1 outputs and can be connected to the analog surround back left and right inputs on a 7.1-channel AV receiver or other component. When using these sockets, the SURR MODE switch should be set to 1+2.

PSURR MODE (AUDIO OUT) switch (37)

This switch is used to set the surround output mode of the analog multichannel audio outputs. If you connect the SURR 2 outputs to a 7.1-channel AV receiver or amp, set this switch to 1+2. This reduces the output level by 3 dB. If you’re not using the SURR 2 outputs, set this switch to 1.

QAV CONNECTOR (32)

This SCART socket outputs RGB video, S-Video, composite video, and analog stereo audio and can be connected to the SCART socket on a TV, projec- tor, or other component.

RHD VIDEO OUT COMPONENT (31)

These BNC sockets output HD component video and can be connected to the HD component video input on an HDTV or projector.

When a video signal is fed to a VIDEO IN socket (S-Video or composite), and the video input source is set to EXTERNAL, that video signal is upcon- verted to progressive and output here.

S12V TRIGGER IN

This socket can be connected to the 12-volt trigger output on an AV receiver or other component so that the DV-SP1000/DV-SP1000E can be turned on remotely.

TAC INLET (41)

The supplied power cord should be connected here.

19