Manuals / Brands / Home Audio / CD Player / Onkyo / Home Audio / CD Player

Onkyo DX-R700 Messages during playback, name input, and other situations (continued)

1 48

Download 48 pages, 969.03 Kb

Troubleshooting guide

Messages during playback, name input, and other situations (continued)

Trouble	Cause	Remedy
The power does	The power cord is not properly	Plug the power cord properly into a mains
not turn on	plugged in.	power supply.

	The component where the power cord is	Turn on the component into which the
	plugged into is not turned on.	power cord is plugged.

No sound is	The speakers are not properly	Connect the speakers following the
output from	connected.	procedure given in “Connecting the
the speakers		DX-R700” on page 15.

Cannot record	The components are not properly	Connect the components following the
	connected.	procedure given in “Connecting the
		DX-R700” on page 15.
	A finalized CD-R or CD-RW is being	Use an unfinalized disc.
	used.

The input switch is not properly set.

Switch to a properly connected input source (see pages 20, 22, 24).

	The recording level adjustment is	Adjust the recording level to a proper level
	set too low.	(see page 21).

Recorded	The components are not properly	Connect the components following the
sound is	connected.	procedure given in “Connecting the
distorted		DX-R700” on page 15.

	Recording is being affected by	Either turn off the television or move the
	the television.	DX-R700 away from the television.
	The disc is damaged or cracked.	Use another disc.
	The recording level adjustment is	Adjust the recording level to a proper level
	set too high.	(see page 21).

	The disc is too dirty.	Clean the disc.

Remote	The remote controller batteries	Replace all the remote controller batteries
controller	are dead.	with new batteries (see page 11).
does not work

There is an object between the DX-R700 and the remote controller obstructing the signals.

Remove the obstructing object (see page 11).

	The remote controller is being used	Use the remote controller within its
	outside of its operational range.	operational range (see page 11).
A recorded	The disc was not finalized	Perform the finalization process
CD-R cannot	after recording.	(see page 33).
be played in	(The CD-R indicator lights when
normal CD	the disc is played with the
players	DX-R700)

45

Contents

Contents Audio CD Recorder Before using Connections Operations16 Thank you for purchasing Main Features WARNING: CAUTION: Important Safeguards Ventilation – Grounding or Polarization – Power-Cord Overloading – Precautions Precautions DANGER: CAUTION: For U.S. model FCC INFORMATION FOR USER Page Table of contents Before Using Connections Operations Other Information Part names and functions Front panel Rear panel RC-448Cremote controller Using the remote controller ■Using the RC-448Cremote controller Installing the remote controller batteries Using the remote controller Notes on usable CDs Notes on discs Connections Connecting the DX-R700 ■Connecting to other components Protection cap for the optical digital input terminal Connecting the DX-R700 1Connecting to an amplifier 2Connecting the zcable 3Connecting to the digital input 4Connecting to the digital output Turning on the power Connecting the power cord Turning the power on Inserting a disc Recording modes Cautions during recording About the level sync function Name function Finalization Erasing recording (CD-RWdiscs only) Digital recording/Analog recording Digital recording/Analog recording 4 Adjust the recording level (1) (2)Press the MULTI JOG dial (3)Turn the MULTI JOG dial to adjust the recording level as desired Synchronous recording by input signal detection (Signal synchronous recording) 1 Repeatedly press the INPUT button and select the desired input signal Synchronous recording by input signal detection (Signal synchronous recording) 6 Press the oREC button Auto finalization •If “Name Disc” appears when you press the FINALIZE button To cancel auto finalization Synchronous recording Synchronous recording to the DX-R700 Synchronous recording 5 Stop the playback of the source device 6 Press the play button on the source device to start the playback When the playback finishes To stop the synchronous recording Using the level sync function Using the level sync function Changing the display Display during recording Entering names Entering a disc name or artist name Entering names 4 Enter a name Types of available easy names To change the type of input characters Using the remote controller (RC-448C)for entering names •Entering an alphabetic character •Entering an easy name To insert a character To erase a character Entering track names Erasing the disc name, artist name, and track names Finalization Erasing recordings (CD-RWdiscs only) Erasing data on non-finalized CD-RWs Erasing recordings (CD-RWdiscs only) ■Erasing the last track or tracks from the selected track to the last track 1 Turn the MULTI JOG dial and select the track to be erased If the selected track is the last track If the selected track is the first track Erasing data on finalized CD-RWs Erasing entire disc Playing CDs Normal playback Playing CDs Random playback Repeat playback With playback stopped, press the RANDOM button Press the REPEAT button as many times as desired Programmed playback Listening with the headphones Other Information Rules concerning digital recording Display messages Troubleshooting guide Troubleshooting guide Messages during recording (continued) Messages during playback, name input, and other situations Messages during playback, name input, and other situations (continued) Specifications Memo ONKYO U.S.A. CORPORATION ONKYO EUROPE ELECTRONICS GmbH ONKYO CHINA LIMITED