Tuner, Remote Controller, UP-A1Dock for iPod

■There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is 61 not guaranteed. In addition, video signals from a PC are not guaranteed.

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

When the AV receiver doesn’t connect TV with	—
HDMI, onscreen menus are not displayed.

Tuner

■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.	—
Move the AV receiver away from your TV or com-	—
puter.
Listen to the station in mono.	24

When listening to an AM station, operating the	—
remote controller may cause noise.
Passing cars and airplanes can cause interference.	—

Concrete walls weaken radio signals.	—
If nothing improves the reception, install an outdoor	—
antenna.

Before operating this unit, be sure to press	—
RECEIVER.

Make sure that the batteries are installed with the	5
correct polarity.
Install new batteries. Don’t mix different types of	5
batteries, or old and new batteries.

Make sure that the remote controller is not too far	5
away from the AV receiver, and that there’s no
obstruction between the remote controller and the
AV receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to	—
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.

If the AV receiver is installed in a rack or cabinet	—
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you’ve selected the correct remote con-	10, 52
troller mode.

When using the remote controller to control other	—
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control	51
code.

Make sure to set the same ID on both the AV receiver	39
and remote controller.

If it’s an Onkyo component, make sure that the u	18
cable and analog audio cable are connected properly.
Connecting only an ucable won’t work.

Make sure you’ve selected the correct remote con-	10, 52
troller mode.

If you’ve connected a cassette tape deck, to the TV/	23
CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
controller to work properly, you must set the display.

If you cannot operate it, you will need to enter the	51
appropriate remote control code.
To control another manufacturer’s component, point	51
the remote controller at that component.

To control an Onkyo component that’s connected via	51
u, point the remote controller at the AV receiver.
Be sure to enter the appropriate remote control code
first.
To control an Onkyo component that’s not connected	51
via u, point the remote controller at the compo-
nent. Be sure to enter the appropriate remote control
code first.

The entered remote control code may not be correct. —
If more than one code is listed, try each one.

Make sure your iPod is actually playing.	—
Make sure your iPod is inserted properly in the	—
Dock.
Make sure the UP-A1 Dock is connected to the UNI- —
VERSAL PORT jack on the AV receiver.

Make sure the AV receiver is turned on, the correct	—
input source is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way.	—

Try resetting your iPod.	—

Make sure that your iPod’s TV OUT setting is set to — On.

Make sure the correct input is selected on your TV or — the AV receiver.

Some versions of the iPod do not output video.

—

■The AV receiver’s remote controller doesn’t control your iPod

Make sure your iPod is properly inserted in the	—
Dock. If your iPod is in a case, it may not connect
properly to the Dock. Always remove your iPod
from the case before inserting it into the Dock.

The iPod cannot be operated while it’s displaying the — Apple logo.

Make sure you’ve selected the right remote mode.	—
When you use the AV receiver’s remote controller,	—
point it toward your AV receiver.
When connecting UP-A1 Dock to the radio tuner	—
UP-HT1(North American models)/UP-DT1
(Asian models) with AUTO selected by the tuner’s
Mode Selector switch, you can switch the input
source between UP-A1 Dock and the tuner, by press-
ing PORT repeatedly on the front panel.

If you still can’t control your iPod, start playback by — pressing your iPod’s Play button. Remote operation should then be possible.

Try resetting your iPod.	—
Depending on your iPod, some buttons may not	—
work as expected.