Onkyo HT-S5300 Sp Config Speaker Configuration, Front, SurrBack Ch, Crossover Crossover Frequency

Cone diameter

Note

•When an HDMI IN is assigned to an input selector in “HDMI Input” (➔ 34), this input assignment is automatically set to the same HDMI IN. And in addition to the usual inputs (e.g., COAX1, COAX2, etc.), you can also select HDMI inputs.

•Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

•If you connect a component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to PORT selector.

Sp Config (Speaker Configuration)

Menu Sp Config

This section explains how to specify

which speakers are connected and their sizes. For speakers with a cone diameter

larger than 6-1/2 inches (16 cm), spec- ify Large (full band). For those with a

smaller diameter, specify Small (default crossover 100 Hz).

The crossover frequency can be changed in the “Crossover (Crossover Frequency)” (➔ 35).

Note

These settings are disabled when:

•a pair of headphones is connected, or

•the “Audio TV OUT” setting is set to “On” (➔ 40) and an input selector other than HDMI is selected.

■Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

■Front

`Small:

`Large:

Select based on the cone diameter.

Note

•If the “Subwoofer” setting is set to “No”, this setting is fixed at “Large” and does not appear.

■Center*1, Surround*1, Front High*1*2*4*6*7, SurrBack*1*2*3*5*7

`Small:

`Large:

Select based on the cone diameter.

`None*6:

Select if no speaker is connected.

Note

*1 If the “Front” setting is set to “Small”, the “Large” option cannot be selected.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “SurrBk/FrontHigh” setting is set to “Front High” (➔ 39), this setting cannot be selected.

*4 If the “Front High/Zone2” setting is set to “Zone2” and “SurrBk/FrontHigh” setting is set to “SurrBack” (➔ 39), this setting cannot be selected.

*5 If the “Surround” setting is set to “Small”, the “Large” option cannot be selected.

*6 For “Front High”, the default is “None”.

*7 If the “Front High/Zone2” setting is set to “Zone2”, this set- ting cannot be selected.

■SurrBack Ch

`1ch:

Select if only one surround back speaker is con- nected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “SurrBack” setting is set to “None”, this setting cannot be selected.

■Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you specified as “Small” in the “Sp Config (Speaker Configura- tion)” (➔ 35). To get the best bass performance from your speaker system, you need to set the crossover fre- quency according to the size and frequency response of your speakers.

`40Hz, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 200Hz:

Use the diameter of the smallest speaker in your system when choosing the crossover frequency.

Speaker cone diameter	Crossover frequency
Over 8 in. (20 cm)	40/50/60 Hz*
6-1/2 to 8 in. (16 to 20 cm)	80 Hz
5-1/4 to 6-1/2 in. (13 to 16 cm)	100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm)	120 Hz
Under 3-1/2 in. (9 cm)	150/200 Hz*

*Choose the setting suitable for the speaker.

Note

•For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly.

•Choose a higher crossover frequency if you want more sound from your subwoofer.

■Double Bass

Note

•This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Large” (➔ 35).

With the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left, right, and center channels to the subwoofer.

`On:

Double Bass function on.

`Off:

Double Bass function off.

En

35