■Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie, Dolby Pro — Logic IIx Music, or Dolby Pro Logic IIx Game lis- tening mode with a mono source, such as an AM radio station or mono TV program, the sound is con- centrated in the center speaker.
Make sure the speakers are configured correctly. | 35 |
■The surround speakers produce no sound
When the | — |
Mono listening mode is selected, the surround |
|
speakers produce no sound. |
|
|
|
Depending on the source and current listening mode, | — |
not much sound may be produced by the surround |
|
speakers. Try selecting another listening mode. |
|
Make sure the speakers are configured correctly. | 35 |
■The center speaker produces no sound
When the Stereo or Mono listening mode is selected, — the center speaker produces no sound.
Make sure the speakers are configured correctly. | 35 |
■The front high or surround back speakers produce no sound
Depending on the current listening mode, no sound | 29 |
may be produced by the front high or surround back |
|
speakers. Select another listening mode. |
|
|
|
Not much sound may be produced by the front high | — |
or surround back speakers with some sources. |
|
Make sure the speakers are configured correctly. | 35 |
|
|
While Powered Zone 2 is being used, playback in the | 44 |
main room is reduced to |
|
high or surround back speakers produce no sound. |
|
|
|
■The subwoofer produces no sound
When you play source material that contains no | — |
information in the LFE channel, the subwoofer pro- |
|
duces no sound. |
|
|
|
Make sure the speakers are configured correctly. | 35 |
|
|
■There’s no sound with a certain signal format
Check the digital audio output setting on the con- | — |
nected device. On some game consoles, such as |
|
those that support DVD, the default setting is off. |
|
|
|
With some | — |
audio output format from a menu. |
|
Depending on the input signal, some listening modes | |
cannot be selected. |
|
■ Can’t get 6.1/7.1 playback
If no surround back speakers or front high speakers — are connected, or the Zone 2 speakers are being
used, 6.1/7.1 playback is not possible.
You can not always select all of the listening modes,
■The volume cannot be set to 79
Check to see if a maximum volume has been set. | 22 |
■Noise can be heard
Using cable ties to bundle audio cables with power — cords, speaker cables, and so on may degrade the audio performance, so don’t do it.
An audio cable may be picking up interference. Try — repositioning your cables.
■The Late Night function doesn’t work
Make sure the source material is Dolby Digital, | 42 |
Dolby Digital Plus, and Dolby TrueHD. |
|
■ About DTS signals
When DTS program material ends and the DTS bit- — stream stops, the AV receiver remains in DTS listen- ing mode and the DTS indicator remains on. This is
to prevent noise when you use the pause, fast for- ward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback.
With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.
When playing DTS program material, using the | — |
pause, fast forward, or fast reverse function on your |
|
player may produce a short audible noise. This is not |
|
amalfunction.
■The beginning of audio received by an HDMI IN can’t be heard
Since it takes longer to identify the format of an | — |
HDMI signal than it does for other digital audio sig- |
|
nals, audio output may not start immediately. |
|
Video
■ There’s no picture
Make sure that all video connecting plugs are pushed | 15 |
in all the way. |
|
|
|
Make sure that each video component is properly | 16, 17, |
connected. | 47 |
If the video source is connected to a component | 17, 34 |
video input, you must assign that input to an input |
|
selector, and your TV must be connected to COM- |
|
PONENT VIDEO MONITOR OUT. |
|
|
|
If the video source is connected to a composite video | 17 |
input, your TV must be connected to the correspond- |
|
ing composite video output. |
|
If the video source is connected to an HDMI input, | 16, 34 |
you must assign that input to an input selector, and |
|
your TV must be connected to the HDMI OUT. |
|
|
|
On your TV, make sure that the video input to which | — |
the AV receiver is connected is selected. |
|
|
|
En
55