■Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie, Dolby Pro — Logic IIx Music, or Dolby Pro Logic IIx Game lis- tening mode with a mono source, such as an AM radio station or mono TV program, the sound is con- centrated in the center speaker.
In the Mono listening mode, only the front speakers | 51 |
output sound if the “Output Speaker” setting is set |
|
to “Center”. |
|
Make sure the speakers are configured correctly. | 48 |
■The surround speakers produce no sound
When the | — |
Mono listening mode is selected, the surround |
|
speakers produce no sound. |
|
|
|
Depending on the source and current listening mode, | — |
not much sound may be produced by the surround |
|
speakers. Try selecting another listening mode. |
|
Make sure the speakers are configured correctly. | 48 |
■The center speaker produces no sound
When the Stereo or Mono listening mode is selected, | — |
the center speaker produces no sound. |
|
|
|
In the Mono listening mode, only the front speakers | 51 |
output sound if the “Output Speaker” setting is set |
|
to “Left / Right”. |
|
Make sure the speakers are configured correctly. | 48 |
■The front high, front wide and surround back speakers produce no sound
Depending on the current listening mode, no sound | 37 |
may be produced by the front high, front wide and |
|
surround back speakers. Select another listening |
|
mode. |
|
|
|
Not much sound may be produced by the front high, | — |
front wide and surround back speakers with some |
|
sources. |
|
Make sure the speakers are configured correctly. | 48 |
■The subwoofer produces no sound
When you play source material that contains no | — |
information in the LFE channel, the subwoofer pro- |
|
duces no sound. |
|
|
|
Make sure the speakers are configured correctly. | 48 |
|
|
■There’s no sound with a certain signal format
Check the digital audio output setting on the con- | — |
nected device. On some game consoles, such as |
|
those that support DVD, the default setting is off. |
|
|
|
With some | — |
audio output format from a menu. |
|
Depending on the input signal, some listening modes | |
cannot be selected. |
|
■Can’t select the Pure Audio listening mode
The Pure Audio listening mode cannot be selected — while Zone 2/3 is on.
■ Can’t get 6.2/7.2 playback
If no surround back speakers, front wide and front | — |
high speakers are connected, or the Zone 2/3 speak- |
|
ers are being used, 6.2/7.2 playback is not possible. |
|
You can not always select all of the listening modes,
■The speaker volume cannot be set as required (The volume cannot be set to Max(100.0))
Check to see if a maximum volume has been set. | 59 |
If the volume level of each individual speaker has | 29, 49 |
been adjusted to high positive values, then the maxi- mum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after Audyssey MultEQ® XT32 Room Correction and Speaker Setup function has been completed.
■Noise can be heard
Using cable ties to bundle audio cables with power — cords, speaker cables, and so on may degrade the audio performance, so don’t do it.
An audio cable may be picking up interference. Try — repositioning your cables.
■The Late Night function doesn’t work
Make sure the source material is Dolby Digital, | 63 |
Dolby Digital Plus, and Dolby TrueHD. |
|
■The analog multichannel input doesn’t work
Check the multichannel input connections. | — |
Make sure that the multichannel input is assigned to | 47 |
the input selector. |
|
Make sure that the multichannel input is selected. | 64 |
Check the audio output settings on your source com- — ponent.
■ About DTS signals
When DTS program material ends and the DTS bit- — stream stops, the AV controller remains in DTS lis- tening mode and the DTS indicator remains on. This
is to prevent noise when you use the pause, fast for- ward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV controller does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback.
With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV con- troller. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV control- ler doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.
When playing DTS program material, using the | — |
pause, fast forward, or fast reverse function on your |
|
player may produce a short audible noise. This is not |
|
amalfunction.
■The beginning of audio received by an HDMI IN can’t be heard
Since it takes longer to identify the format of an | — |
HDMI signal than it does for other digital audio sig- |
|
nals, audio output may not start immediately. |
|
En
95
