Firmware Update

There are the following methods to update the firmware: via network and via USB storage. Please choose either one that suits your condition. Before you start, carefully read the update procedure. It will take about 60 minutes to update the firmware.

Update via network

You need a wired Internet connection to update the firmware.

Update via USB storage (105)

Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of avail- able space to update the firmware.

Note

The storage media in the USB card reader may not work.

If the storage device has been partitioned, each section will be treated as an independent device.

If the USB mass storage device contains a lot of data, the AV controller may take a while to read it.

Operation with all USB mass storage devices including the abil- ity to power them is not guaranteed.

Onkyo accepts no responsibility whatsoever for the loss or dam- age to data stored on a USB mass storage device when that device is used with the AV controller. We recommend that you back up your important music files beforehand.

If you connect a USB hard disk drive to the USB port, we rec- ommend that you use its AC adapter to power it.

USB hubs and USB devices with hub functions are not sup- ported. Do not connect your USB mass storage device via a USB hub.

USB memory devices with security functions are not supported.

In no event shall Onkyo be liable to you or any third party for any damages, whatsoever, arising from your use of or inability to use the firmware, including but not limited to, loss of any equipment, media or data, or other special, incidental or consequential dam- ages, even if Onkyo has been advised of the possibility of such damages.

See the Onkyo web site for latest information.

Updating the Firmware via Network

The AV controller allows you to update firmware using net- work connection on rear panel.

*In this procedure, on-screen display may vary depending on the model.

Note

Make sure your AV controller and TV are turned on and Ethernet cable is connected to rear panel of the AV controller.

Never unplug or turn off the AV controller during updating pro- cess.

Never plug or unplug an HDMI cable and Ethernet cable during updating process.

Never unplug the power cord during updating process.

Do not access the AV controller from PC during updating pro- cess.

It will take about 60 minutes to update the firmware.

The AV controller will retain all your settings after update is fin- ished.

En

Before you start

Check “HDMI Control(RIHD)” setting (61). The update may not be successful if this setting is on.

Turn off the controller device connected via RS232C and via Ethernet network.

Turn off Zone 2 and Zone 3.

Stop playback of content from Internet radio, iPod, USB or servers, etc.

How to turn off RIHD

 

 

1

In the Main menu select “Hardware Setup”.

2

Select “HDMI”.

3

Set “HDMI Control(RIHD)” to “Off”.

Update procedure

 

 

 

 

1

Press RECEIVER followed by SETUP on the

 

remote controller.

 

Main menu will be displayed on TV screen. Proce-

 

dures thereafter can also be performed on the AV

 

controller by using its SETUP, arrow, and ENTER

 

buttons.

 

 

2

Go to “Hardware Setup” menu.

3

Go to “Firmware Update” menu.

 

Note that the Firmware Update option will be grayed

 

out about 50 seconds after the AV controller is

 

turned on. Please wait.

 

 

4

Select “via NET” and press ENTER.

5

Select “Update” and press ENTER.

 

Updating will begin.

 

As the updating progresses, the TV screen may dis-

 

appear depending on the program updated. In this

 

case, you can see the update progress on the front

 

display of the AV controller. The TV screen will

 

reappear when you finish the update and turn on the

 

AV controller.

 

 

6

Message “Complete!” appears on the front dis-

 

play of the AV controller, indicating that the

 

update has been completed.

 

 

7

Using ON/STANDBY on the front panel, turn off

 

and on the AV controller.

Do not use ON or STANDBY on the remote control- ler.

Congratulations!! Now you have the latest firmware on your Onkyo AV controller.

104

Page 104
Image 104
Onkyo PR-SC5508 instruction manual Firmware Update, Updating the Firmware via Network, Before you start, Update procedure