Panasonic AJ-D455P operating instructions Edit Setting Description

Setup menus

USER menu

<EDIT> (continued)

	Item		Setting
							Description
No.	Superimposed	No.		Superimposed
	display			display
313	AFTER	0000				STOP	This selects the mode after cue-up operation is complete.
	CUE-UP	0001				STILL1	0: STOP mode
		0002				STILL2	1: SHTL STILL mode
							2: VAR STILL mode
315	AUD MEM	0000				OFF	This selects the connection with the AJ-YA752 audio memory
	UNIT	0001				MODE1	unit.
		0002				MODE2	0: When the audio memory unit is not going to be used
		0003				MODE3	1: When a voice-over operation is to be conducted
							2: When audio cross channel editing is to be performed for
							CH2
							3: When audio cross channel editing is to be performed for
							CH1
							<Notes>
							• The RS-232C interface will function only when this menu
							item is set to 0 (OFF).
							• Refer to the Instruction Manual of the AJ-YA752 audio
							memory unit for details on how the modes are used.
316	VAR STEP	0000				FINE	This selects the VAR speed during remote control operations.
		0001			COARSE		0: The tape is played at the fine step speed.
							1: The tape is played at a speed at which noise-less playback
							is possible in the –0.43⋅to +1⋅ (–0.5⋅to +1⋅ ) range.
							<Notes>
							• The speeds in parentheses apply when a DV or DVCAM
							cassette is used.
							• At the 1(COARSE) setting, the phase cannot be synchro-
							nized from the editing controller.
317	VAR FWD	0000			+4.1		This sets the maximum VAR FWD speed.
	MAX	0001		+1.85			0: +4.1⋅ (+3.1⋅ ) speed
		0002		+1			1: +1.85⋅ (+1.85⋅ ) speed
							2: +1⋅ (+1⋅ ) speed
							<Notes>
							• The speeds in parentheses apply when a DV or DVCAM
							cassette is used.
							• At any speed setting other than 0 (+4.1⋅ ), the phase cannot
							be synchronized from the editing controller.
318	VAR REV	0000				–4.1	This sets the maximum VAR REV speed.
	MAX	0001				–1.85	0: –4.1⋅(–3.1⋅) speed
		0002				–1	1: –1.85⋅(–1.85⋅) speed
							2: –1⋅(–1⋅) speed
		0003				–0.43
							3: –0.43⋅(–0.5⋅) speed
							<Note>
							The speeds in parentheses apply when a DV or DVCAM
							cassette is used.
319	JOG STEP	0000				FINE	This selects the JOG speed during remote control operations.
		0001			COARSE		0: The tape is played at the fine step speed.
							1: The tape is played at a speed at which noise-less playback
							is possible in the –0.43⋅to +1⋅ (–0.5⋅to +1⋅ ) range.
							<Notes>
							• The speeds in parentheses apply when a DV or DVCAM
							cassette is used.
							• At the 1(COARSE) setting, the phase cannot be synchro-
							nized from an editing controller which synchronizes the
							phase using the JOG command.

The underline on the setting item denotes the initial setting.

28